Re: Plus d'infos ?

Salut, alors oui, dans mon /dev, je trouve bien mes disques "locaux" mais pas ceux du FibreChannel:

# ls -l /dev/disk/by-id/
total 0
lrwxrwxrwx 1 root root 9 2007年10月23日 19:36 scsi-3500000e015cffd20 -> ../../sdb
lrwxrwxrwx 1 root root 9 2007年10月23日 19:36 scsi-3500000e015cffeb0 -> ../../sda
lrwxrwxrwx 1 root root 10 2007年10月23日 19:36 scsi-3500000e015cffeb0-part1 -> ../../sda1
lrwxrwxrwx 1 root root 10 2007年10月23日 19:36 scsi-3500000e015cffeb0-part2 -> ../../sda2
lrwxrwxrwx 1 root root 10 2007年10月23日 19:36 scsi-3500000e015cffeb0-part5 -> ../../sda5

sda est mon disque système (une partition et un swap) et sdb est un autre disque que je n'utilise pas pour l'instant. Pour le dmesg, je le mets ci-dessous en entier (je voulais le couper, mais j'ai peur de râter des choses importantes...) Dedans, on peut voir que la carte FC est bien reconnue (Emulex blabla) et même que mon SAN répond (FibreCat, c'est son nom). J'ai mis en gras les parties qui semblent intéressantes. Par contre, j'ai des scsi generic (sg0 à 4) et je ne vois pas trop à quoi correspondent les 2 derniers... Je suppose que les premiers sont mes 2 disques et mon cdrom.

Linux version 2.6.18-4-686 (Debian 2.6.18.dfsg.1-12) (waldi@debian.org) (gcc version 4.1.2 20061115 
(prerelease) (Debian 4.1.1-21)) #1 SMP Mon Mar 26 17:17:36 UTC 2007
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009e400 (usable)
 BIOS-e820: 000000000009e400 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000ce000 - 00000000000d0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000007fee0000 (usable)
 BIOS-e820: 000000007fee0000 - 000000007fee7000 (ACPI data)
 BIOS-e820: 000000007fee7000 - 000000007ff00000 (ACPI NVS)
 BIOS-e820: 000000007ff00000 - 000000007ff80000 (usable)
 BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
 BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
 BIOS-e820: 00000000fe000000 - 00000000fed00000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fef00000 (reserved)
 BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
1151MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f7a70
On node 0 totalpages: 524160
 DMA zone: 4096 pages, LIFO batch:0
 Normal zone: 225280 pages, LIFO batch:31
 HighMem zone: 294784 pages, LIFO batch:31
DMI present.
ACPI: RSDP (v002 PTLTD ) @ 0x000f7a00
ACPI: XSDT (v001 PTLTD XSDT 0x06040001 LTP 0x00000000) @ 0x7fee3949
ACPI: FADT (v003 FSC 0x06040001 0x000f4240) @ 0x7fee3a11
ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040001 PTL 0x00000001) @ 0x7fee6e9c
ACPI: MCFG (v001 PTLTD MCFG 0x06040001 LTP 0x00000000) @ 0x7fee6eec
ACPI: HPET (v001 PTLTD HPETTBL 0x06040001 LTP 0x00000001) @ 0x7fee6f2c
ACPI: MADT (v001 PTLTD APIC 0x06040001 LTP 0x00000000) @ 0x7fee6f64
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040001 LTP 0x00000001) @ 0x7fee6fd8
ACPI: DSDT (v001 FSC D2300 0x06040001 MSFT 0x03000000) @ 0x00000000
ACPI: PM-Timer IO Port: 0xf008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 6:15 APIC version 20
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
Processor #1 6:15 APIC version 20
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec80000] gsi_base[24])
IOAPIC[1]: apic_id 3, version 32, address 0xfec80000, GSI 24-47
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 2 I/O APICs
ACPI: HPET id: 0x8086a201 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 88000000 (gap: 80000000:60000000)
Detected 1595.963 MHz processor.
Built 1 zonelists. Total pages: 524160
Kernel command line: root=/dev/sda1 ro 
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
mapped IOAPIC to ffffb000 (fec80000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 16384 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 2070960k/2096640k available (1544k kernel code, 24292k reserved, 577k data, 196k init, 11790
08k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
hpet0: at MMIO 0xfed00000 (virtual 0xf8800000), IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Using HPET for base-timer
Calibrating delay using timer specific routine.. 3194.48 BogoMIPS (lpj=6388960)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0004e33d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0004e33d 00000000 00000001
monitor/mwait feature present.
using mwait in idle threads.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0004e33d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
CPU0: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06
SMP alternatives: switching to SMP code
Booting processor 1/1 eip 3000
Initializing CPU#1
Calibrating delay using timer specific routine.. 3191.93 BogoMIPS (lpj=6383875)
CPU: After generic identify, caps: bfebfbff 20100000 00000000 00000000 0004e33d 00000000 00000001
CPU: After vendor identify, caps: bfebfbff 20100000 00000000 00000000 0004e33d 00000000 00000001
monitor/mwait feature present.
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 4096K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
CPU: After all inits, caps: bfebfbff 20100000 00000000 00000940 0004e33d 00000000 00000001
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#1.
CPU1: Intel(R) Xeon(R) CPU 5110 @ 1.60GHz stepping 06
Total of 2 processors activated (6386.41 BogoMIPS).
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
checking TSC synchronization across 2 CPUs: passed.
Brought up 2 CPUs
migration_cost=54
checking if image is initramfs... it is
Freeing initrd memory: 4371k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: Using MMCONFIG
PCI: No mmconfig possible on c:5
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller .&checktime(0000,00,1,':')f.2
Boot video device is 0000:0c:05.0
PCI: Transparent bridge - .&checktime(0000,00,1,':')e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2_.PSU_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2_.PSU_.PSD1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2_.PSU_.PSD2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE2_.PXH0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE4_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PE6_.PXH1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIH._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 *9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: Device [COM2] status [00000008]: functional but not present; setting present
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Bridge: .&checktime(0000,02,00,':').0
 IO window: disabled.
 MEM window: disabled.
 PREFETCH window: disabled.
PCI: Bridge: .&checktime(0000,02,01,':').0
 IO window: disabled.
 MEM window: disabled.
 PREFETCH window: disabled.
PCI: Bridge: .&checktime(0000,01,00,':').0
 IO window: disabled.
 MEM window: disabled.
 PREFETCH window: disabled.
PCI: Bridge: .&checktime(0000,01,00,':').3
 IO window: 3000-3fff
 MEM window: fc100000-fc7fffff
 PREFETCH window: 88000000-883fffff
PCI: Bridge: .&checktime(0000,00,02,':').0
 IO window: 3000-3fff
 MEM window: fc100000-fc7fffff
 PREFETCH window: 88000000-883fffff
PCI: Bridge: .&checktime(0000,00,03,':').0
 IO window: disabled.
 MEM window: disabled.
 PREFETCH window: disabled.
PCI: Bridge: .&checktime(0000,07,00,':').0
 IO window: disabled.
 MEM window: fc800000-fc8fffff
 PREFETCH window: disabled.
PCI: Bridge: .&checktime(0000,00,04,':').0
 IO window: disabled.
 MEM window: fc800000-fc8fffff
 PREFETCH window: disabled.
PCI: Bridge: .&checktime(0000,00,05,':').0
 IO window: disabled.
 MEM window: disabled.pcie_portdrv_probe->Dev[25f7:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,00,02,':').0:pcie00]
Allocate Port Service[.&checktime(0000,00,02,':').0:pcie01]
PCI: Setting latency timer of device .&checktime(0000,00,03,':').0 to 64
pcie_portdrv_probe->Dev[25e3:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,00,03,':').0:pcie00]
Allocate Port Service[.&checktime(0000,00,03,':').0:pcie01]
PCI: Setting latency timer of device .&checktime(0000,00,04,':').0 to 64
pcie_portdrv_probe->Dev[25e4:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,00,04,':').0:pcie00]
Allocate Port Service[.&checktime(0000,00,04,':').0:pcie01]
PCI: Setting latency timer of device .&checktime(0000,00,05,':').0 to 64
pcie_portdrv_probe->Dev[25e5:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,00,05,':').0:pcie00]
Allocate Port Service[.&checktime(0000,00,05,':').0:pcie01]
PCI: Setting latency timer of device .&checktime(0000,00,06,':').0 to 64
pcie_portdrv_probe->Dev[25f9:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,00,06,':').0:pcie00]
Allocate Port Service[.&checktime(0000,00,06,':').0:pcie01]
PCI: Setting latency timer of device .&checktime(0000,00,07,':').0 to 64
pcie_portdrv_probe->Dev[25e7:8086] has invalid IRQ. Check vendor BIOS
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,00,07,':').0:pcie00]
Allocate Port Service[.&checktime(0000,00,07,':').0:pcie01]
PCI: Setting latency timer of device .&checktime(0000,01,00,':').0 to 64
Allocate Port Service[.&checktime(0000,01,00,':').0:pcie10]
Allocate Port Service[.&checktime(0000,01,00,':').0:pcie11]
PCI: Setting latency timer of device .&checktime(0000,02,00,':').0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,02,00,':').0:pcie20]
Allocate Port Service[.&checktime(0000,02,00,':').0:pcie21]
PCI: Setting latency timer of device .&checktime(0000,02,01,':').0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[.&checktime(0000,02,01,':').0:pcie20]
Allocate Port Service[.&checktime(0000,02,01,':').0:pcie21]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
hpet_resources: 0xfed00000 is busy
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:KEYB,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Starting balanced_irq
Using IPI No-Shortcut mode
ACPI: (supports S0 S1 S4 S5)
Freeing unused kernel memory: 196k freed
Time: tsc clocksource has been installed.
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x8
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x8
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x8
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x8
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x8
ACPI Exception (acpi_processor-0681): AE_NOT_FOUND, Processor Device is not present [20060707]
ACPI: Getting cpuindex for acpiid 0x8
tg3.c:v3.65 (August 07, 2006)
ACPI: PCI Interrupt .&checktime(0000,08,04,':').0[A] -> GSI 16 (level, low) -> IRQ 169
eth0: Tigon3 [partno(BCM95715) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00
:0a:e4:82:97:56
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1] 
eth0: dma_rwctrl[76148000] dma_mask[64-bit]
ACPI: PCI Interrupt .&checktime(0000,08,04,':').1[B] -> GSI 17 (level, low) -> IRQ 177
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SCSI subsystem initialized
Emulex LightPulse Fibre Channel SCSI driver 8.1.9
Copyright(c) 2004-2006 Emulex. All rights reserved.
eth1: Tigon3 [partno(BCM95715) rev 9003 PHY(5714)] (PCIX:133MHz:64-bit) 10/100/1000BaseT Ethernet 00
:0a:e4:82:97:57
eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] Split[0] WireSpeed[1] TSOcap[1] 
eth1: dma_rwctrl[76148000] dma_mask[64-bit]
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt 0000:0a:00.0[A] -> GSI 16 (level, low) -> IRQ 169
PCI: Setting latency timer of device 0000:0a:00.0 to 64
scsi0 : on PCI bus 0a device 00 irq 169
libata version 2.00 loaded.
Fusion MPT base driver 3.04.01
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SAS Host driver 3.04.01
lpfc 0000:0a:00.0: 0:1303 Link Up Event x1 received Data: x1 x1 x8 x3
 Vendor: FSC Model: FibreCAT_SX1 Rev: J110
 Type: Enclosure ANSI SCSI revision: 03
 Vendor: FSC Model: FibreCAT_SX1 Rev: J110
 Type: Enclosure ANSI SCSI revision: 03
ACPI: PCI Interrupt .&checktime(0000,00,1,':')d.7[A] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device .&checktime(0000,00,1,':')d.7 to 64
ehci_hcd .&checktime(0000,00,1,':')d.7: EHCI Host Controller
ehci_hcd .&checktime(0000,00,1,':')d.7: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device .&checktime(0000,00,1,':')d.7
ehci_hcd .&checktime(0000,00,1,':')d.7: irq 66, io mem 0xfc000000
ehci_hcd .&checktime(0000,00,1,':')d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ACPI: PCI Interrupt .&checktime(0000,00,1,':')d.0[A] -> GSI 23 (level, low) -> IRQ 66
PCI: Setting latency timer of device .&checktime(0000,00,1,':')d.0 to 64
uhci_hcd .&checktime(0000,00,1,':')d.0: UHCI Host Controller
uhci_hcd .&checktime(0000,00,1,':')d.0: new USB bus registered, assigned bus number 2
uhci_hcd .&checktime(0000,00,1,':')d.0: irq 66, io base 0x00001000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt .&checktime(0000,00,1,':')d.1[B] -> GSI 22 (level, low) -> IRQ 74
PCI: Setting latency timer of device .&checktime(0000,00,1,':')d.1 to 64
uhci_hcd .&checktime(0000,00,1,':')d.1: UHCI Host Controller
uhci_hcd .&checktime(0000,00,1,':')d.1: new USB bus registered, assigned bus number 3
uhci_hcd .&checktime(0000,00,1,':')d.1: irq 74, io base 0x00001400
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt .&checktime(0000,00,1,':')d.2[C] -> GSI 21 (level, low) -> IRQ 82
PCI: Setting latency timer of device .&checktime(0000,00,1,':')d.2 to 64
uhci_hcd .&checktime(0000,00,1,':')d.2: UHCI Host Controller
uhci_hcd .&checktime(0000,00,1,':')d.2: new USB bus registered, assigned bus number 4
uhci_hcd .&checktime(0000,00,1,':')d.2: irq 82, io base 0x00001800
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt .&checktime(0000,00,1,':')d.3[D] -> GSI 20 (level, low) -> IRQ 90
PCI: Setting latency timer of device .&checktime(0000,00,1,':')d.3 to 64
uhci_hcd .&checktime(0000,00,1,':')d.3: UHCI Host Controller
uhci_hcd .&checktime(0000,00,1,':')d.3: new USB bus registered, assigned bus number 5
uhci_hcd .&checktime(0000,00,1,':')d.3: irq 90, io base 0x00001c00
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt .&checktime(0000,05,05,':').0[A] -> GSI 24 (level, low) -> IRQ 98
ata_piix .&checktime(0000,00,1,':')f.2: version 2.00
ata_piix .&checktime(0000,00,1,':')f.2: MAP [ P0 P2 IDE IDE ]
mptbase: Initiating ioc0 bringup
ACPI: PCI Interrupt .&checktime(0000,00,1,':')f.2[B] -> GSI 19 (level, low) -> IRQ 106
PCI: Setting latency timer of device .&checktime(0000,00,1,':')f.2 to 64
ata1: SATA max UDMA/133 cmd 0x1F0 ctl 0x3F6 bmdma 0x2400 irq 14
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0x1F7
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x2408 irq 15
scsi2 : ata_piix
ata2.01: ATAPI, max UDMA/33
ioc0: SAS1068: Capabilities={Initiator}
ata2.01: configured for UDMA/33
 Vendor: HL-DT-ST Model: RW/DVD GCC-4244N Rev: 1.00
 Type: CD-ROM ANSI SCSI revision: 05
scsi3 : ioc0: LSISAS1068, FwRev=01122800h, Ports=1, MaxQ=511, IRQ=98
 Vendor: FUJITSU Model: MAY2073RC Rev: 5204
 Type: Direct-Access ANSI SCSI revision: 03
 Vendor: FUJITSU Model: MAY2073RC Rev: 5204
 Type: Direct-Access ANSI SCSI revision: 03
SCSI device sda: 143374744 512-byte hdwr sectors (73408 MB)
sda: Write Protect is off
sda: Mode Sense: dd 00 00 08
SCSI device sda: drive cache: write through
SCSI device sda: 143374744 512-byte hdwr sectors (73408 MB)
sda: Write Protect is off
sda: Mode Sense: dd 00 00 08
SCSI device sda: drive cache: write through
 sda: sda1 sda2 < sda5 >
sd 3:0:0:0: Attached scsi disk sda
SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB)
sdb: Write Protect is off
sdb: Mode Sense: dd 00 00 08
SCSI device sdb: drive cache: write through
SCSI device sdb: 143374744 512-byte hdwr sectors (73408 MB)
sdb: Write Protect is off
sdb: Mode Sense: dd 00 00 08
SCSI device sdb: drive cache: write through
 sdb: unknown partition table
sd 3:0:1:0: Attached scsi disk sdb
Attempting manual resume
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 2:0:1:0: Attached scsi CD-ROM sr0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
scsi 0:0:0:0: Attached scsi generic sg0 type 13
scsi 0:0:1:0: Attached scsi generic sg1 type 13
sr 2:0:1:0: Attached scsi generic sg2 type 5
sd 3:0:0:0: Attached scsi generic sg3 type 0
sd 3:0:1:0: Attached scsi generic sg4 type 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
Real Time Clock Driver v1.12ac
intel_rng: FWH not detected
ACPI: PCI Interrupt .&checktime(0000,00,1,':')f.3[B] -> GSI 19 (level, low) -> IRQ 106
input: PC Speaker as /class/input/input1
logips2pp: Detected unknown logitech mouse model 0
Adding 2650684k swap on /dev/sda5. Priority:-1 extents:1 across:2650684k
EXT3 FS on sda1, internal journal
input: ImPS/2 Logitech Wheel Mouse as /class/input/input2
ts: Compaq touchscreen protocol output
loop: loaded (max 8 devices)
device-mapper: ioctl: 4.7.0-ioctl (2006年06月24日) initialised: dm-devel@redhat.com
PM: Writing back config space on device .&checktime(0000,08,04,':').0 at offset 3 (was 804000, writing 804010)
PM: Writing back config space on device .&checktime(0000,08,04,':').0 at offset 1 (was 2b00000, writing 2b00146)
tg3: eth0: Link is up at 100 Mbps, full duplex.
tg3: eth0: Flow control is off for TX and off for RX.
ACPI: Power Button (FF) [PWRF]
ACPI: Power Button (CM) [PWRB]
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present