< Exactement tu pense faire quoi la ?
une connerie, effectivement
Rectificatif
adresse de ma carte réseau 192.168.1.6 sur eth0
adresse ethernet MAC de l'imprimante 00:80:77:87:01:77
arp -s 192.168.1.5 00:80:77:87:01:77 -i eth0
arp -a
? (192.168.1.1) at 00:0C:C3:31:DA:29 [ether] on ra0
? (192.168.1.5) at 00:80:77:87:01:77 [ether] PERM on eth0
nmap -P0 192.168.1.5
Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2007年05月13日 23:08 CEST
Nmap finished: 1 IP address (0 hosts up) scanned in 0.282 seconds
Impossible de pinguer 192.168.1.5
DOC CUPS
Getting the IP Address
When you first install a network printer or print server on your LAN, you need to set the Internet Protocol ("IP") address. On most higher-end "workgroup" printers, you can set the address through the printer control panel. However, in most cases you will want to assign the addresses remotely from your workstation. This makes administration a bit easier and avoids assigning duplicate addresses accidentally.
To setup your printer or print server for remote address assignment, you'll need the Ethernet Media Access Control ("MAC") address, also sometimes called a node address, and the IP address you want to use for the device. The Ethernet MAC address can often be found on the printer test page or bottom of the print server.
Configuring the IP Address Using ARP
The easiest way to set the IP address of a network device is to use the arp(8) command. The arp sends an Address Resolution Protocol ("ARP") packet to the specified Ethernet MAC address, setting the network device's IP address:
[^] # Re: Re
Posté par vat . En réponse au message configuration imprimante réseau. Évalué à 1.
< Exactement tu pense faire quoi la ?
une connerie, effectivement
Rectificatif
adresse de ma carte réseau 192.168.1.6 sur eth0
adresse ethernet MAC de l'imprimante 00:80:77:87:01:77
arp -s 192.168.1.5 00:80:77:87:01:77 -i eth0
arp -a
? (192.168.1.1) at 00:0C:C3:31:DA:29 [ether] on ra0
? (192.168.1.5) at 00:80:77:87:01:77 [ether] PERM on eth0
nmap -P0 192.168.1.5
Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2007年05月13日 23:08 CEST
Nmap finished: 1 IP address (0 hosts up) scanned in 0.282 seconds
Impossible de pinguer 192.168.1.5
DOC CUPS
Getting the IP Address
When you first install a network printer or print server on your LAN, you need to set the Internet Protocol ("IP") address. On most higher-end "workgroup" printers, you can set the address through the printer control panel. However, in most cases you will want to assign the addresses remotely from your workstation. This makes administration a bit easier and avoids assigning duplicate addresses accidentally.
To setup your printer or print server for remote address assignment, you'll need the Ethernet Media Access Control ("MAC") address, also sometimes called a node address, and the IP address you want to use for the device. The Ethernet MAC address can often be found on the printer test page or bottom of the print server.
Configuring the IP Address Using ARP
The easiest way to set the IP address of a network device is to use the arp(8) command. The arp sends an Address Resolution Protocol ("ARP") packet to the specified Ethernet MAC address, setting the network device's IP address:
arp -s ip-address ethernet-address
arp -s host.domain.com 08:00:69:00:12:34
arp -s 192.0.2.2 08:00:69:00:12:34