• [^] # Re: Ouhla !

    Posté par . En réponse au message je m'inquiète. Évalué à 1.

    autre chose, le routeur adsl fait de la redirection de ports (du NATdynamic), j'ai qu'une bécane sur le réseau mais je compte faire quelquechose de la connexion wireless...
    j'ai ouvert des ports pour le traffic p2p.

    aussi ça:

    eth0: Tigon3 [partno(BCM95702A20) rev 1002 PHY(5703)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet XXXXXXXXXXXXXx
    eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[1] TSOcap[1]
    eth0: dma_rwctrl[763f0000] dma_mask[64-bit]

    encore ça:
    PM: Writing back config space on device .&checktime(0000,02,05,':').0 at offset b (was 164714e4, writing 80a91043)
    PM: Writing back config space on device .&checktime(0000,02,05,':').0 at offset 3 (was 0, writing 4008)
    PM: Writing back config space on device .&checktime(0000,02,05,':').0 at offset 2 (was 2000000, writing 2000002)
    PM: Writing back config space on device .&checktime(0000,02,05,':').0 at offset 1 (was 2b00000, writing 2b00006)
    PM: Writing back config space on device .&checktime(0000,02,05,':').0 at offset 0 (was 164714e4, writing 16a614e4)

    et ça:tg3: eth0: Link is up at 100 Mbps, full duplex.
    tg3: eth0: Flow control is off for TX and off for RX.
    PCI: Enabling device .&checktime(0000,02,0,':')a.0 (0014 -> 0016)
    ACPI: PCI Interrupt .&checktime(0000,02,0,':')a.0[A] -> GSI 22 (level, low) -> IRQ 22
    rt2500 1.1.0 CVS 2005年07月10日 http://rt2x00.serialmonkey.com
    rt2500 EEPROM: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Channel
    rt2500 EEPROM: 11 11 11 11 11 11 11 11 11 11 11 11 11 11 dBm Maximum
    CSLIP: code copyright 1989 Regents of the University of California
    PPP generic driver version 2.4.2
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    printk: 20030 messages suppressed.
    Neighbour table overflow.
    printk: 19875 messages suppressed.
    tg3: eth0: Link is down.
    tg3: eth0: Link is up at 100 Mbps, full duplex.
    tg3: eth0: Flow control is off for TX and off for RX.
    tg3: eth0: Link is down.
    tg3: eth0: Link is up at 100 Mbps, full duplex.
    tg3: eth0: Flow control is off for TX and off for RX.
    tg3: eth0: Link is down.
    tg3: eth0: Link is up at 100 Mbps, full duplex.
    tg3: eth0: Flow control is off for TX and off for RX.
    tg3: eth0: Link is down.
    tg3: eth0: Link is up at 100 Mbps, full duplex.
    tg3: eth0: Flow control is off for TX and off for RX.
    ISO 9660 Extensions: Microsoft Joliet Level 1
    ISOFS: changing to secondary root
    printk: 13611 messages suppressed.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    Neighbour table overflow.
    printk: 13441 messages suppressed.
    Neighbour table overflow.
    printk: 7115 messages suppressed.
    Neighbour table overflow.
    printk: 5276 messages suppressed.
    Neighbour table overflow.
    printk: 5611 messages suppressed.
    Neighbour table overflow.
    printk: 14002 messages suppressed.
    Neighbour table overflow.
    printk: 12884 messages suppressed.
    Neighbour table overflow.
    VFS: busy inodes on changed media.
    VFS: busy inodes on changed media.

    OULALALAL le kernel compilé de ce matin crache une pléthore d'anomalies...

    j'ai pas tout mis mais y a de quoi remplir 3 écrans, cest grave docteur? mon ADSL fonctionne pourtant... en faisant un ptit ifup eth0 à la mimine.