[LOGic] Logic 8 and Microham Interfaces

Tue Feb 12 11:13:54 EST 2008

Hi Mel:
I know this is hard to understand or accept, but when devices work with most computers and they do not work with yours, chances are there is something wrong with your computer. Especially when they are set up the same way & with the same equipment. There is probably some stupid setting in the registry that is causing the problem. Probably made by some other program. I have been computing since the VIC 20 and most of the times that there have been problems they were on my end and I consider my self very computer literate. I am not suggesting that you do this, but I would bet that if you reinstalled Windows and then installed Logic, your problems would be resolved. I personally have only done this once in my life because my registry was so large. It is a shame that when you uninstall programs almost all of them leave there settings and garbage behind. Take it easy on Dennis. Every problem I have ever had with Logic was resolved with a phone call.
Good Luck, Lloyd NX4W
 ---- Mel Martin <ve2dc at videotron.ca> wrote: 
> Roland... they shouldn't be checked. I am sure that if you uncheck yours 
> it will still work.
>> BTW, is your processor a dual core or single CPU?
>> Mine is a single CPU... older Pentium 4.
>> Roland Guidry wrote:
> > Stan,
> > 
> > I have the exact same setup as you with the Pro 3, but using Microham Keyer
> > with USB too. The only difference in your configuration and mine is in
> > Logic. I have both DTR and RTS checked under rig control. 
> > 
> > Give it a try.
> > 
> > Roland NA5Q
> > 
> > Message: 7
> > Date: 2008年2月11日 11:06:31 -0600
> > From: Stan <k9iuq at verizon.net>
> > Subject: Re: [LOGic] Logic 8 and Microham Interfaces
> > To: LOGic is open to all radio amateurs for discussion of LOGic
> > 	logging	program <logic at mailman.qth.net>
> > Message-ID: <47B08097.8030203 at verizon.net>
> > Content-Type: text/plain; charset=ISO-8859-1; format=flowed
> > 
> > Mel
> > Interface= Microham USB II
> > Version : USB device Router 5.1.1 - the latest version available at 
> > Microham website
> > Radio= Icom Pro III, Ci-V baud rate 19200, CI-V address 6Eh, Ci-V 
> > transceive On, Ci-V transceive with IC-731 off
> > 
> > Microham USB device router Set up:
> > Radio Com1, CW Com5 DTR, PTT Com5 RTS, SQL none
> > 
> > This setup works flawlessly with over a dozen programs I have tried in 
> > the last 2 years.
> > 
> > Logic 8 goes into transmit when I load the program. Also goes into 
> > transmit when I access and exit the Rig setup menu. Also goes into 
> > transmit when I access certain other
> > menus like Utilitys. Only way to get it out of transmit is to remove 
> > the interface USB plug and re-insert. In Logic 8 I have radio1 setup as 
> > Icom all, com1, 19200 2 stop bits Addr 6Eh, DTR and RTS not checked.
> > 
> > I dont have the CW keying setup in LOgic right now. Logic sends very 
> > poor CW, it stutters and sometimes shortens dits or dahs. I been using 
> > Mixw to send CW , since it sends perfectly. Mixw 2 uses the Com 3 port 
> > and is not setup for the rig control. I have tried running Logic 8 by 
> > itself thinking maybe MIXW was interfering but this is not the case.
> > 
> > I have tried other different setups both in Logic and the Device router 
> > with same results.
> > 
> > Thanks
> > Stan K9IUQ
> > 
> > 
> > _______________________________________________
> > LOGic mailing list
> > LOGic at mailman.qth.net
> > http://mailman.qth.net/mailman/listinfo/logic
> > 
> _______________________________________________
> LOGic mailing list
> LOGic at mailman.qth.net
> http://mailman.qth.net/mailman/listinfo/logic