Implement the ladder logic program needed to satisfy each of the following (assume inputs A, B and C are all normally open toggle switches). (a) When input A is closed, turn on output X, but hold on output Y until A opens. (b) When input A is closed and either input B or C is open, turn on output Y, otherwise it should be off. (c) When input A is closed or open, turn on output Y and turn off output X. (d) When input A is closed, turn on output X and turn off output Y.

The numbers from 0-9 and a no characters is the Basic 1 digit seven segment display * .can show False True In a (CA) method of 7 segments, the anodes of all the LED segments are * "connected to the logic "O False True Some times may run out of pins on your Arduino board and need to not extend it * .with shift registers True False

Please help me fill in the worksheet. And for the second part of the worksheet you have to make that circuit on TinkerCAD, with leds, etc.

Mention Written Answer Needed Correct one

Written Answer Needed Correct one

Needs Complete solution with 100 % accuracy.

8- is flip-flop which indicates some condition which arises after the execution of an arithmetic or logic instruction. a) Status flag b) Instruction registers c) Temporary register d) None of these 9- El instruction is a_ a) Branching Instructions b) Logical Instructions c) Control Instructions d) Data Transfer Instruction e) Arithmetic Instructions

12) Study the ladder logic program in the figure below and answer the questions that follow: a. What is the purpose of interconnecting the two timers? b. How much time must elapse before output PL is energized? c. What two conditions must be satisfied for timer T4:2 to start timing? d. Assume that output PL is on and power to the system is lost. When power is restored, what will the status of this output be? e. When input PB2 is on, what will happen? f. When input PB1 is on, how much accumulate. Ladder logic program Output PB2 L2 T4:1 (RES Inputs L1 T4:2 (RES PB1 PL PB2 -RTO PB1 RETENTIVE TIMER ON T4:1 EN 1.0 2900 CON) Timer Time base Preset Accumulated -RTO PB1 T4:1 RETENTIVE TIMER ON Timer Time base T4:2 (EN) 1.0 DN Preset 1780 ON) Accumulated T4:2 PL HE DN

12) Study the ladder logic program in the figure below and answer the questions that follow: a. What is the purpose of interconnecting the two timers? b. How much time must elapse before output PL is energized? c. What two conditions must be satisfied for timer T4:2 to start timing? d. Assume that output PL is on and power to the system is lost. When power is restored, what will the status of this output be? e. When input PB2 is on, what will happen? f. When input PB1 is on, how much accumulate. Ladder logic program Output PB2 L2 T4:1 Inputs (RES L1 T4:2 PB1 (RES) PLO PB2 -RTO - RETENTIVE TIMER ON PB1 Timer Time base Preset T4:1EN) 1.0 2900 CON) Accumulated -RTO- PB1 T4:1 RETENTIVE TIMER ON Timer Time base T4:2 (EN) 1.0 DN Preset Accumulated 1780 CON) T4:2 PL DN

Please give typed solution only

Draw the output waveform C and D, given the input waveforms A and B as shown belowfigure 2.Figure 2b) Verify the result from part (a) by any using simulation tools. (Screen shoot only for thefollowing input cases: when (A=0, B=0), (A=1, B=0) and (A=0, B=1). c) For the logic circuit given in Figure 3, obtain the output expression for ?

Study the ladder logic program in figure below and answer the questions that follows: a) What type of timer has been programmed? Explain the timers function in detail with suitable graph: b) What is the length of the time-delay period? c) What is the value of the accumulated time when power is first applied? d) When does the timer start timing? e) When does the timer stop timing and reset itself? Input LS1 Outputs L1 TON L2 TIMER ON DELAY Timer Time base Preset KEN T4:0 LS1 ISOL A-o 1 10 KON) Accumulated SOL B- T4:0 SOL A DN T4:0 SOL B 3 DN T4:0 EN T4.0 EN

Plz solve within 30min I vill give definitely upvote and vill give positive feedback thank you sir