Antenna factor

Antennas
Part of a series on

Common types Dipole Fractal Loop Monopole Satellite dish Television Whip
Components Balun Block upconverter Coaxial cable Counterpoise (ground system) Feed Feed line Low-noise block downconverter Passive radiator Receiver Rotator Stub Transmitter Tuner Twin-lead
Systems Antenna farm Amateur radio Cellular network Hotspot Municipal wireless network Radio Radio masts and towers Wi-Fi Wireless
Safety and regulation Wireless device radiation and health Wireless electronic devices and health International Telecommunication Union (Radio Regulations) World Radiocommunication Conference
Radiation sources / regions Boresight Focal cloud Ground plane Main lobe Near and far field Side lobe Vertical plane
Characteristics Array gain Directivity Efficiency Electrical length Equivalent radius Factor Friis transmission equation Gain Height Radiation pattern Radiation resistance Radio propagation Radio spectrum Signal-to-noise ratio Spurious emission
Techniques Beam steering Beam tilt Beamforming Small cell Bell Laboratories Layered Space-Time (BLAST) Massive Multiple-input multiple-output (MIMO) Reconfiguration Spread spectrum Wideband Space Division Multiple Access (WSDMA)
v t e

In electromagnetics, the antenna factor (AF, units: m⁻¹, reciprocal meter) is defined as the ratio of the electric field E (units: V/m or μV/m) to the voltage V (units: V or μV) induced across the terminals of an antenna:

AF={\frac {E}{V}}

{\displaystyle AF={\frac {E}{V}}}

If all quantities are expressed logarithmically in decibels instead of SI units, the above equation becomes

AF_{\mathrm {dB/m} }=E_{\mathrm {\mathrm {dBV/m} } }-V_{\mathrm {dBV} }

{\displaystyle AF_{\mathrm {dB/m} }=E_{\mathrm {\mathrm {dBV/m} } }-V_{\mathrm {dBV} }}

The voltage measured at the output terminals of an antenna is not the actual field intensity due to actual antenna gain, aperture characteristics, and loading effects.^[1]^{[clarification needed ]}

For a magnetic field, with units of A/m, the corresponding antenna factor is in units of A/(V⋅m). For the relationship between the electric and magnetic fields, see the impedance of free space.

For a 50 Ω load, knowing that P_D A_e = P_r = V²/R and E²= ${\sqrt {\frac {\mu _{0}}{\varepsilon _{0}}}}$ {\displaystyle {\sqrt {\frac {\mu _{0}}{\varepsilon _{0}}}}}P_D ~ 377P_D (E and V noted here are the RMS values averaged over time), the antenna factor is developed as:

AF={\frac {\sqrt {377P_{D}}}{\sqrt {50P_{D}A_{e}}}}={\frac {2.75}{\sqrt {A_{e}}}}={\frac {9.73}{\lambda {\sqrt {G}}}}

{\displaystyle AF={\frac {\sqrt {377P_{D}}}{\sqrt {50P_{D}A_{e}}}}={\frac {2.75}{\sqrt {A_{e}}}}={\frac {9.73}{\lambda {\sqrt {G}}}}}

Where

A_e = (λ²G)/4π : the antenna effective aperture
P_D is the power density in watts per unit area
P_r is the power delivered into the load resistance presented by the receiver (normally 50 ohms)
G: the antenna gain
$\mu _{0}$ {\displaystyle \mu _{0}} is the magnetic constant
$\varepsilon _{0}$ {\displaystyle \varepsilon _{0}} is the electric constant

For antennas which are not defined by a physical area, such as monopoles and dipoles consisting of thin rod conductors, the effective length (units: meter) is used to measure the ratio between voltage and electric field.