[Logic] Error in Logic 6.0

2002年4月20日 10:20:34 -0500

I just did the import. I am not sure if the problem is with the import
routine. It seems I had this once before and it is a header file not
included but may not be needed for the import to work In any case, I got the
import and all the data seems to be there .
I cannot test it as I cannot remember how to make it show up in the log
form. I have the data but cannot use it until I figure out how to make it
appear. :-)
> -----Original Message-----
> From: [email protected] [mailto:[email protected]]On
> Behalf Of Stephen J. Schrack
> Sent: Saturday, April 20, 2002 10:09 AM
> To: [email protected]
> Subject: RE: [Logic] Error in Logic 6.0
>>> Hello Roland and ALL,
>> Yes as stated before and below I am experiencing the same issue. I also
> had the same error message when importing the 1010.txt list. So, Roland
> I suspect the problem lies in the import routine as suggested in my
> earlier post that it was suspect. But, you're experiment narrows it
> down to the import routine. Please email Dennis and I will contact him
> as well...Tnx for sharing your results Roland. Best 73 De N3MX...
>> -----Original Message-----
> From: [email protected] [mailto:[email protected]]
> On Behalf Of Roland Guidry
> Sent: Saturday, April 20, 2002 10:30 AM
> To: [email protected]
> Subject: Re: [Logic] Error in Logic 6.0
>> I went into my list table and deleted the 1010# list. I then imported a
> older list from March 2002. Doing this,did not cure the problem.
> Cleaning
> indexes and updating awards did not help. I did get an error when trying
> to
> import the 1010.txt file.
> "prg12e.err [Read Only]" -
> #include 'pda.h'
> Error in line 3: File does not exist.
> When I ignore the error, it loads data.
>> Does anyone have any suggestions.
>> Roland
>>>>> ----- Original Message -----
> From: "Stephen J. Schrack" <[email protected]>
> To: <[email protected]>
> Sent: Saturday, April 20, 2002 8:08 AM
> Subject: RE: [Logic] Error in Logic 6.0
>>> > I am experiencing a similar problem, but not quite the same. Mine only
> > happens when the 1010 number is a high number. In other words, The
> 1010
> > automatic lookup (or manual) works fine until the 1010 number happens
> to
> > be one of the higher numbers (60,000 or higher). Then I get the error
> > message described below. Sometimes I can recover from that though. I
> > suspect it is a corruption of the 1010 list and was going to wait and
> > see if the next 1010.txt has the same issue. Perhaps the corruption
> > takes place during import? My platform is WinXP Professional 384MB RAM
> > on a 1ghz workstation.
> >
> > Best 73 de N3MX...STEVE
> >
> > -----Original Message-----
> > From: [email protected] [mailto:[email protected]]
> > On Behalf Of Roland Guidry
> > Sent: Saturday, April 20, 2002 8:39 AM
> > To: [email protected]
> > Subject: [Logic] Error in Logic 6.0
> >
> > I am have difficulty with this new program, Logic 6.0 Build 6.0.104.
> > When my
> > cursor passes over the userfield 1010#, I get an error as shown with
> the
> > attached gif pic. When I chose "no" the program exits and when
> > restarted, I
> > have to perform a clean then restart.
> >
> > Sometime I get an error message that says "Invalid Subscript
> Reference"
> > Cancel or Ignore. If I "Ignore" program continues to run, if I cancel
> I
> > get
> > other errors reported.
> >
> > The file I downloaded for 1010#'s came from Win1010 using their
> 1010.txt
> > file. I do not have this problem with Logic 5.
> >
> > Has anyone encountered this same problem. I email [email protected] on
> > 4/18,
> > no response to date.
> >
> > Roland, WA5CHX
> >
> >
> > _______________________________________________
> > LOGic mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/logic
> >
> >
> >
> > _______________________________________________
> > LOGic mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/logic
> >
>>> _______________________________________________
> LOGic mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/logic
>>>> _______________________________________________
> LOGic mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/logic
>