Imizekelo yokubala - Shenzhen HONGSBELT

Umhambisi othe tye

Kwifektri yokumisa inyama, ubushushu be-ambient bulawulwa kwi-21 ° C, kwaye yamkelwe i-HS-100 yomgca wokumisa inyama.Ubunzima obuqhelekileyo benyama yi-60kg/M2.Ububanzi bebhanti yi-600mm, kwaye ubude obupheleleyo bomthumeli ngu-30M kwi-design ethe tye.Isantya sokusebenza sebhanti lokuhambisa yi-18M/min kwindawo yokufuma nokubanda.Umhambisi uqala ekothuleni kwaye akukho mqathango wandayo.Yamkela i-sprockets enamazinyo ayi-8 kwi-192mm ububanzi, kunye ne-38mm x 38mm ye-stainless steel drive shaft.Ifomula yokubala efanelekileyo yile ilandelayo.

Ukubalwa koxinzelelo lwethiyori yeyunithi - TB

IFOMU :

TB =〔 ( WP + 2 WB ) ×ばつ FBW + Wf ×ばつ L + ( WP ×ばつ H )

TB =〔 ( 60 + ( 2 ×ばつ 8.6 ) ×ばつ 0.12 ×ばつ 30 = 278 (kg / M)

Ngenxa yokuba ayilulo ukuhanjiswa kwemfumba, iWf inokungahoywa.

Ukubalwa kweyunithi yoxinzelelo lulonke - TW

IFOMU :

TW = TB ×ばつ FA

TW = 278 ×ばつ 1.0 = 278 ( Kg / M )

Ukubalwa kweyunithi yoxinzelelo oluvumelekileyo - TA

IFOMU : TA = BS ×ばつ FS ×ばつ FT

TA = 1445 ×ばつ 1.0 ×ばつ 0.95 = 1372.75 ( Kg / M )

Ngenxa yexabiso le-TA likhulu kune-TW, Ngoko ke, ukwamkela nge-HS-100 kukhetho olufanelekileyo.

Nceda ubhekisele kwisithuba seSprocket se-HS-100 kwiSahluko se-Drive Sprockets;isithuba esikhulu se-sprocket simalunga ne-140mm kolu yilo.Zombini i-drive/Idler end of conveyor kufuneka ibekwe nge-3 sprockets.

I-Deflection ratio ye-drive shaft - i-DS

IFOMU : SL = ( TW + SW ) ×ばつ BW

SL = ( 278 + 11.48 ) ×ばつ 0.6 = 173.7 ( Kg )

Xa kuthelekiswa ne-Maximum Torque Factor kwiyunithi ye-Shaft Selection, siyazi ukuba ukusetyenziswa kwe-38mm ×ばつ 38mm square shaft kukhuselekile kwaye kukhethwe ngokufanelekileyo.

IFOMU : DS = 5 ×ばつ 10-4 ×ばつ ( SL x SB3 / E x I )

DS = 5 ×ばつ 10-4 ×ばつ [ (173.7 ×ばつ 7003 ) / ( 19700 ×ばつ 174817 )] = 0.0086

Ukuba isiphumo sobalo sincinci kunexabiso elisemgangathweni elidweliswe kwiTheyibhile yokuPhambuka;ukwamkela iibheringi ezimbini zebhola kwanele kwinkqubo.

Ukubalwa kwe-shaft torque - TS

IFOMU :

TS = TW ×ばつ BW ×ばつ R

TS = 10675 ( kg - mm )

Xa kuthelekiswa ne-Maximum Torque Factor kwiyunithi yokuKhethwa kweShaft, siyazi ukuba ukusetyenziswa kwe-50mm ×ばつ 50mm square shaft kukhuselekile kwaye kukhethwe ngokufanelekileyo.

Ukubalwa kwamandla eHashe - HP

IFOMU :

HP = 2.2 ×ばつ 10-4 ×ばつ [ ( TS ×ばつ V ) / R ]

I-HP = 2.2 ×ばつ 10-4 ×ばつ [ ( 10675 ×ばつ 10 ) / 66.5] = 0.32 ( HP )

Ngokubanzi, amandla omatshini wokuhambisa umbane angaphulukana ne-11% ngexesha lokusebenza.

MHP = [ 0.32 / (100 - 11 ) ×ばつ 100 = 0.35 ( HP )

Ukwamkela i-1/2HP drive motor lukhetho olufanelekileyo.

Sidwelisa imizekelo esebenzayo kwesi sahluko kwireferensi yakho, kwaye sikukhokele ukuba ubalele uvavanyo kunye nokuqinisekisa iziphumo zokubala.

Umhambisi oqhutywa kwiziko

I-conveyor eqokelelweyo ihlala isetyenziswa kwishishini lesiselo.Uyilo lomqhubi yi-2M ububanzi kunye ne-6M ubude besakhelo esipheleleyo.Isantya sokusebenza somthumeli sikwi-20M/min;iqala kwimeko yeemveliso eziqokelelana kwibhanti kwaye isebenze kwindawo eyomileyo eyi-30°C.Ukulayishwa kwebhanti yi-80Kg / m2 kunye neemveliso zokuthutha iikhenki ze-aluminium kunye nesiselo ngaphakathi.I-wearstrips yenziwe ngezinto ze-UHMW, kwaye yamkelwe i-Series 100BIP, i-sprocket yensimbi engenasici enamazinyo angama-10, kunye ne-stainless steel drive / i-idler shaft kwi-50mm x 50mm ubukhulu.Iifomula zokubala ezifanelekileyo zezi zilandelayo.

Ukunyuka kokuhanjiswa - Wf

IFOMU :

Wf = WP ×ばつ FBP ×ばつ PP

Wf = 80 ×ばつ 0.4 ×ばつ 1 = 32 ( Kg / M )

Ukubalwa koxinzelelo lwethiyori yeyunithi - TB

IFOMU :

TB =〔 ( WP + 2 WB ) ×ばつ FBW + Wf ×ばつ L + ( WP ×ばつ H )

TB =〔 ( 100 + ( 2 ×ばつ 8.6 ) ×ばつ 0.12 + 32 ×ばつ 6 + 0 = 276.4 (kg / M)

Ukubalwa kweyunithi yoxinzelelo lulonke- TW

IFOMU :

TW = TB ×ばつ FA

TW = 276.4 ×ばつ 1.6 = 442 ( Kg / M )

TWS = 2 TW = 884 Kg / M

I-TWS yayo ingundoqo wokuqhuba

Ukubalwa kweyunithi yoxinzelelo oluvumelekileyo - TA

IFOMU :

TA = BS ×ばつ FS ×ばつ FT

TA = 1445 ×ばつ 1.0 ×ばつ 0.95 = 1372 ( Kg / M )

Ngenxa yexabiso le-TA likhulu kune-TW, Ngoko ke, ukwamkela nge-HS-100 kukhetho olufanelekileyo.

Nceda ubhekisele kwisithuba seSprocket se-HS-100 kwiSahluko se-Drive Sprockets;isithuba esikhulu se-sprocket simalunga ne-120mm kolu yilo.
I-Deflection ratio ye-drive shaft - i-DS

IFOMU :

SL = ( TW + SW ) ×ばつ BW

SL = ( 884 + 19.87 ) ×ばつ 2 = 1807 ( Kg )

DS = 5 ×ばつ 10-4 [ ( SL ×ばつ SB3 ) / ( E ×ばつ I )]

DS = 5 ×ばつ 10-4 ×ばつ [ ( 1791 ×ばつ 21003 ) / ( 19700 ×ばつ 1352750 )] = 0.3 mm

Ukuba isiphumo sobalo sincinci kunexabiso elisemgangathweni elidweliswe kwiTheyibhile yokuPhambuka;ukwamkela iibheringi ezimbini zebhola kwanele kwinkqubo.

Ukubalwa kwe-shaft torque - TS

IFOMU :

TS = TWS ×ばつ BW ×ばつ R

TS = 884 ×ばつかける 2 ×ばつかける 97 =わ 171496 ( kg - mm)

Xa kuthelekiswa ne-Maximum Torque Factor kwiyunithi yokuKhethwa kweShaft, siyazi ukuba ukusetyenziswa kwe-50mm ×ばつ 50mm square shaft kukhuselekile kwaye kukhethwe ngokufanelekileyo.

Ukubalwa kwamandla eHashe - HP

IFOMU :

I-HP = 2.2 ×ばつ 10-4 [ ( TS ×ばつ V ) / R ]

HP =2.2 ×ばつ 10-4 ×ばつ [ ( 171496 ×ばつ 4 ) / 82] = 1.84 ( HP )

Ngokubanzi, amandla omatshini wokujika anokuphulukana ne-25% ngexesha lokusebenza.

MHP = [ 1.84 / ( 100 - 25 )] ×ばつ 100 = 2.45 ( HP )

Ukwamkela i-3HP drive motor lukhetho olufanelekileyo.

Cofa kwiConveyor

I-incline conveyor system ibonisa kulo mfanekiso ungasentla yenzelwe ukuhlamba imifuno.Ubude bayo obuthe nkqo yi-4M, ubude obupheleleyo bomthumeli yi-10M, kunye nobubanzi bebhanti yi-900mm.Isebenza kwindawo yomswakama kunye nesantya se-20M / min ukuthutha ii-peas kwi-60Kg / M2.I-wearstrips yenziwe ngezinto ze-UHMW, kwaye ibhanti lokuhambisa yi-HS-200B kunye ne-50mm (H) iindiza kunye ne-60mm (H) yabalindi becala.Inkqubo iqala kwimeko ngaphandle kokuthwala iimveliso, kwaye igcina ukusebenza ubuncinane kwiiyure ze-7.5.Ikwamkele kunye ne-sprockets enamazinyo ali-12 kunye nentsimbi engatyiwa 38mm x 38mm drive/idler shaft.Iifomula zokubala ezifanelekileyo zezi zilandelayo.

Ukubalwa koxinzelelo lwethiyori yeyunithi - TB

IFOMU :

TB =〔( WP + 2WB ) ×ばつ FBW + Wf ×ばつ L + ( WP ×ばつ H )

TB =〔( 60 + ( 2 ×ばつ 4.4 ) ×ばつ 0.12 + 0 ) ×ばつ 10 + ( 60 ×ばつ 4 ) = 322.6 ( kg / M )

Ngenxa yoko ayikokuqokelelwa kokuhanjiswa,Wf inokungahoywa.

Ukubalwa kweyunithi yoxinzelelo lulonke - TW

IFOMU :

TW = TB ×ばつ FA

TW = 322.6 ×ばつ 1.6 = 516.2 ( Kg / M )

Ukubalwa kweyunithi yoxinzelelo oluvumelekileyo - TA

IFOMU :

TA = BS ×ばつ FS ×ばつ FT

TA = 980 ×ばつ 1.0 ×ばつ 0.95 = 931

Ngenxa yexabiso i-TA inkulu kune-TW;ngoko ke, ukwamkela ibhanti lokuhambisa iHS-200BFP lukhetho olukhuselekileyo nolufanelekileyo.

Nceda ubhekisele kwisithuba seSprocket se-HS-200 kwiSahluko se-Drive Sprockets;isithuba esikhulu se-sprocket simalunga nama-85mm kolu yilo.
I-Deflection ratio ye-drive shaft - i-DS

IFOMU :

SL = ( TW + SW ) ×ばつ BW

SL = ( 516.2 + 11.48 ) ×ばつ 0.9 = 475 Kg

IFOMU :

DS = 5 ×ばつ 10-4 ×ばつ [ ( SL x SB3 ) / ( E x I )]

DS = 5 ×ばつ 10-4 ×ばつ [ ( 475 ×ばつ 10003 ) / ( 19700 ×ばつ 174817 )] = 0.069 mm

Ukuba isiphumo sobalo sincinci kunexabiso elisemgangathweni elidweliswe kwiTheyibhile yokuPhambuka;ukwamkela iibheringi ezimbini zebhola kwanele kwinkqubo.

Ukubalwa kwe-shaft torque - TS

IFOMU :

TS = TW ×ばつ BW ×ばつ R

TS = 322.6 ×ばつ 0.9 ×ばつ 49 = 14227 ( kg - mm)

Xa kuthelekiswa ne-Maximum Torque Factor kwiyunithi ye-Shaft Selection, siyazi ukuba ukusetyenziswa kwe-38mm ×ばつ 38mm square shaft kukhuselekile kwaye kukhethwe ngokufanelekileyo.

Ukubalwa kwamandla eHashe - HP

IFOMU :

HP = 2.2 ×ばつ 10-4 ×ばつ [ ( TS ×ばつ V ) / R ]

I-HP = 2.2 ×ばつ 10-4 ×ばつ [ ( 14227 ×ばつ 20 ) / 49] = 1.28 ( HP )

Ngokubanzi, amandla omatshini wokujika anokuphulukana ne-20% ngexesha lokusebenza.

MHP = [ 1.28 / ( 100 - 20 )] ×ばつ 100 = 1.6 ( HP )

Ukwamkela i-2HP drive motor lukhetho olufanelekileyo.

Ukuguqula iConveyor

Inkqubo yokuhambisa i-conveyor kumfanekiso ongentla yi-90 degree converting conveyor. I-wearstrips kwindlela yokubuyisela kunye nendlela yokuthwala zombini zenziwe ngezinto ze-HDPE.Ububanzi bebhanti yokuhambisa yi-500mm;ithatha ibhanti le-HS-500B kunye ne-sprockets enamazinyo angama-24.Ubude becandelo elisebenzayo elithe ngqo yi-2M ekupheleni kwe-idler kunye ne-2M ekupheleni kwe-drive.Iradiyasi yayo yangaphakathi yi-1200mm.I-friction factor ye-wearstrips kunye nebhanti yi-0.15.Izinto zokuthutha ziibhokisi zeebhokisi ezikwi-60Kg/M2.Isantya sokusebenza komthumeli yi-4M/min, kwaye sisebenza kwindawo eyomileyo.Ubalo olunxulumeneyo lulandelayo.

Ukubalwa kweyunithi yoxinzelelo lulonke - TWS

IFOMU :

TWS = ( TN )

Uxinzelelo olupheleleyo lwecandelo lokuqhuba kwindlela yokuthwala.

T0 = 0

T1 = WB + FBW ×ばつ LR ×ばつ WB

T1 = 5.9 + 0.35 ×ばつ 2 ×ばつ ( 5.9) = 10.1

IFOMU : TN = ( Ca ×ばつ TN-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

Uxinzelelo lwecandelo lokujika kwindlela yokubuya.Ngexabiso le-Ca kunye ne-Cb, nceda ubhekisele kwiTheyibhile Fc.

T2 = ( Ca ×ばつ T2-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

TN = ( Ca ×ばつ T1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

T2 = ( 1.27 ×ばつ 10.1 ) + ( 0.15 ×ばつ 0.35 ×ばつ 1.7 ) ×ばつ 5.9 = 13.35

IFOMU : TN = TN-1 + FBW ×ばつ LR ×ばつ WB

Uxinzelelo lwecandelo elithe tye kwindlela yokubuya.

T3 = T3-1 + FBW ×ばつ LR ×ばつ WB

T3 = T2 + FBW ×ばつ LR ×ばつ WB

T3 = 13.35 + 0.35 ×ばつ 2 ×ばつ 5.9 = 17.5

IFOMU : TN = TN-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

T4 = T4-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

T4 = T3 + FBW ×ばつ LP ×ばつ ( WB + WP )

T4 = 17.5 + 0.35 ×ばつ 2 ×ばつ ( 5.9 + 60 ) = 63.6

Uxinzelelo lwecandelo elithe tye kwindlela yokuthwala.

IFOMU : TN = ( Ca ×ばつ TN-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

Uxinzelelo lwecandelo lokujika kwindlela yokubuya.Ngexabiso le-Ca kunye ne-Cb, nceda ubhekisele kwiTheyibhile Fc.

T5 = ( Ca ×ばつ T5-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

T5 = ( Ca ×ばつ T6 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

T5 = ( 1.27 ×ばつ 63.6 ) + ( 0.15 ×ばつ 0.35 ×ばつ 1.7 ) ×ばつ ( 5.9 + 60 ) = 86.7

Iyonke ingcinezelo yebhanti TWS (T6)

IFOMU :

TWS = T6 = TN-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

Uxinzelelo olupheleleyo lwecandelo elithe tye kwindlela yokuthwala.

T6 = T6-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

T6 = T5 + FBW ×ばつ LP ×ばつ ( WB + WP )

T6 = 86.7 + 0.35 ×ばつ 2 ×ばつ ( 5.9 + 60 ) = 132.8 ( Kg / M )

Ukubalwa kweyunithi yoxinzelelo oluvumelekileyo - TA

IFOMU :

TA = BS ×ばつ FS ×ばつ FT

TA = 2118 ×ばつ 1.0 ×ばつ 0.95 = 2012 ( Kg / M )

Ngenxa yexabiso i-TA inkulu kune-TW;ngoko ke, ukwamkela Series 500B ibhanti lokuhambisa kukhetho olukhuselekileyo nolufanelekileyo.

Nceda ubhekisele kwisithuba seSprocket se-HS-500 kwiSahluko se-Drive Sprockets;isithuba esikhulu se-sprocket simalunga ne-145mm.
I-Deflection ratio ye-drive shaft - i-DS

IFOMU :

SL = ( TWS + SW ) ×ばつBW

SL = ( 132.8 + 11.48 ) ×ばつ 0.5 = 72.14 ( Kg )

IFOMU :

DS = 5 ×ばつ 10-4 ×ばつ [ ( SL ×ばつ SB3 ) / ( E ×ばつ I )]

DS = 5 ×ばつ 10-4 ×ばつ [ ( 72.14 ×ばつ 6003 ) / ( 19700 ×ばつ 174817 )] = 0.002 ( mm)

Ukuba isiphumo sobalo sincinci kunexabiso elisemgangathweni elidweliswe kwiTheyibhile yokuPhambuka;ukwamkela iibheringi ezimbini zebhola kwanele kwinkqubo.

Ukubalwa kwe-shaft torque - TS

IFOMU :

TS = TWS ×ばつ BW ×ばつ R

TS = 132.8 ×ばつ 0.5 ×ばつ 92.5 = 6142 (kg - mm)

Xa kuthelekiswa ne-Maximum Torque Factor kwiyunithi yokuKhethwa kweShaft, siyazi ukuba ukusetyenziswa kwe-50mm ×ばつ 50mm square shaft kukhuselekile kwaye kukhethwe ngokufanelekileyo.

Ukubalwa kwamandla eHashe - HP

IFOMU :

HP = 2.2 ×ばつ 10-4 ×ばつ [ ( TS ×ばつ V / R )]

I-HP = 2.2 ×ばつ 10-4 ×ばつ [ ( 6142 ×ばつ 4 ) / 95] = 0.057 ( HP )

Ngokubanzi, amandla omatshini wokujika anokuphulukana ne-30% ngexesha lokusebenza.

MHP = [ 0.057 / ( 100 - 30 )] ×ばつ 100 = 0.08 ( HP )

Ukwamkela i-1/4HP drive motor lukhetho olufanelekileyo.

Uthotho Turning Conveyor

Uthotho-Ujiko-Conveyor

Isixokelelwano sokuhambisa esijikelezayo sakhiwe ngabahambisi ababini be-90 degree kunye necala elichaseneyo.I-wearstrips ngendlela yokubuyisela kunye nendlela yokuthwala zombini zenziwe ngezinto ze-HDPE.Ububanzi bebhanti yokuhambisa yi-300mm;ithatha ibhanti le-HS-300B kunye ne-sprockets enamazinyo ayi-12.Ubude becandelo elisebenzayo elichanekileyo li-2M ekupheleni kwe-idler, i-600mm kwindawo yokudibanisa, kunye ne-2M ekupheleni kwe-drive.I-radius yayo yangaphakathi yi-750mm.I-friction factor ye-wearstrips kunye nebhanti yi-0.15.Izinto zokuthutha ziibhokisi zeplastiki kwi-40Kg/M2.Isantya sokusebenza komthumeli si-5M/min, kwaye sisebenza kwindawo eyomileyo.Ubalo olunxulumeneyo lulandelayo.

Ukubalwa kweyunithi yoxinzelelo lulonke - TWS

IFOMU :

TWS = ( TN )

T0 = 0

Uxinzelelo olupheleleyo lwecandelo lokuqhuba kwindlela yokuthwala.

T1 = WB + FBW ×ばつ LR ×ばつ WB

T1 = 5.9 + 0.35 ×ばつ 2 ×ばつ 5.9 = 10.1

IFOMU :

TN = ( Ca ×ばつ TN-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

Uxinzelelo lwecandelo lokujika kwindlela yokubuya.Ngexabiso le-Ca kunye ne-Cb, nceda ubhekisele kwiTheyibhile Fc.

T2 = ( Ca ×ばつ T2-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

T2 = ( Ca ×ばつ T1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

T2 = ( 1.27 ×ばつ 10.1) + ( 0.15 ×ばつ 0.35 ×ばつ 1.05 ) ×ばつ 5.9 = 13.15

IFOMU :

TN = TN-1 + FBW ×ばつ LR ×ばつ WB

Uxinzelelo lwecandelo elithe tye kwindlela yokubuya.

T3 = T3-1 + FBW ×ばつ LR ×ばつ WB

T3 = T2 + FBW ×ばつ LR ×ばつ WB

T3 = 13.15 + ( 0.35 ×ばつ 0.6 ×ばつ 5.9 ) = 14.3

IFOMU :

TN = ( Ca ×ばつ TN-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

Uxinzelelo lwecandelo lokujika kwindlela yokubuya.Ngexabiso le-Ca kunye ne-Cb, nceda ubhekisele kwiTheyibhile Fc.

T4 = ( Ca ×ばつ T4-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

TN = ( Ca ×ばつ T3 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ WB

T4 = ( 1.27 ×ばつ 14.3 ) + ( 0.15 ×ばつ 0.35 ×ばつ 1.05 ) ×ばつ 5.9 = 18.49

IFOMU :

TN = TN-1 + FBW ×ばつ LR ×ばつ WB

Uxinzelelo lwecandelo elithe tye kwindlela yokubuya.

T5 = T5-1 + FBW ×ばつ LR ×ばつ WB

T5 = T4 + FBW ×ばつ LR ×ばつ WB

T5 = 18.49 + ( 0.35 ×ばつ 2 ×ばつ 5.9 ) = 22.6

IFOMU :

TN = TN-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

Uxinzelelo lwecandelo elithe tye kwindlela yokuthwala.

T6 = T6-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

T6 = T5 + FBW ×ばつ LP ×ばつ ( WB + WP )

T6 = 22.6 + [ ( 0.35 ×ばつ 2 ×ばつ ( 5.9 + 40 ) ] = 54.7

IFOMU :

TN = ( Ca ×ばつ TN-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

Uxinzelelo lwecandelo lokujika kwindlela yokuthwala.Ngexabiso le-Ca kunye ne-Cb, nceda ubhekisele kwiTheyibhile Fc

T7 = ( Ca ×ばつ T7-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

T7 = ( Ca ×ばつ T6 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

T7 = ( 1.27 ×ばつ 54.7 ) + ( 0.15 ×ばつ 0.35 ×ばつ 1.05 ) ×ばつ ( 40 + 5.9 ) = 72

IFOMU :

TN = TN-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

Uxinzelelo lwecandelo elithe tye kwindlela yokuthwala.

T8 = T8-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

TN = T7 + FBW ×ばつ LP ×ばつ ( WB + WP )

T8 = 72 + [ ( 0.35 ×ばつ 0.5 ×ばつ ( 40 + 5.9 ) ] = 80

IFOMU :

TN = ( Ca ×ばつ TN-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

Uxinzelelo lwecandelo lokujika kwindlela yokuthwala.Ngexabiso le-Ca kunye ne-Cb, nceda ubhekisele kwiTheyibhile Fc

T9 = ( Ca ×ばつ T9-1 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

T9 = ( Ca ×ばつ T8 ) + ( Cb ×ばつ FBW ×ばつ RO ) ×ばつ ( WB + WP )

T9 = ( 1.27 ×ばつ 80 ) + ( 0.15 ×ばつ 0.35 ×ばつ 1.05 ) ×ばつ ( 40 + 5.9 ) =104

Iyonke ingcinezelo yebhanti TWS (T6)

IFOMU :

TWS = T10

Uxinzelelo olupheleleyo lwecandelo elithe tye kwindlela yokuthwala.

TN = TN-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

T10 = T10-1 + FBW ×ばつ LP ×ばつ ( WB + WP )

T10 = 104 + 0.35 ×ばつ 2 ×ばつ ( 5.9 + 40 ) = 136.13 ( Kg / M )

Ukubalwa kweyunithi yoxinzelelo oluvumelekileyo - TA

IFOMU :

TA = BS ×ばつ FS ×ばつ FT

TA = 2118 ×ばつ 1.0 ×ばつ 0.95 = 2012 ( Kg / M )

Ngenxa yexabiso i-TA inkulu kune-TW;ngoko ke, ukwamkela Series 300B ibhanti lokuhambisa kukhetho olukhuselekileyo nolufanelekileyo.

Nceda ubhekisele kwisithuba seSprocket kwiSahluko seDrive Sprockets;isithuba esikhulu se-sprocket simalunga ne-145mm.
I-Deflection ratio ye-drive shaft - i-DS

IFOMU :

SL = ( TWS + SW ) ×ばつ BW

SL = ( 136.13 + 11.48 ) ×ばつ 0.3 = 44.28 ( Kg )

IFOMU :

DS = 5 ×ばつ 10-4 ×ばつ [ ( SL ×ばつ SB3 ) / ( E x I )]

DS = 5 ×ばつ 10-4 ×ばつ [ ( 44.28 ×ばつ 4003 ) / ( 19700 ×ばつ 174817 ) = 0.000001 ( mm)

Ukuba isiphumo sobalo sincinci kunexabiso elisemgangathweni elidweliswe kwiTheyibhile yokuPhambuka;ukwamkela iibheringi ezimbini zebhola kwanele kwinkqubo.

Ukubalwa kwe-shaft torque - Ts

IFOMU :

TS = TWS ×ばつ BW ×ばつ R

TS = 136.3 ×ばつ 0.3 ×ばつ 92.5 = 3782.3 ( kg - mm)

Xa kuthelekiswa ne-Maximum Torque Factor kwiyunithi ye-Shaft Selection, siyazi ukuba ukusetyenziswa kwe-38mm ×ばつ 38mm square shaft kukhuselekile kwaye kukhethwe ngokufanelekileyo.

Calc, ulat, io, n of horsepower - HP

IFOMU :

HP = 2.2 ×ばつ 10-4 ×ばつ [ ( TS ×ばつ V ) / R ]

I-HP = 2.2 ×ばつ 10-4 ×ばつ [ ( 3782.3 ×ばつ 5 ) / 92.5] = 0.045 ( HP )

Ngokubanzi, amandla omatshini we-center drive conveyor anokulahlekelwa malunga ne-30% ngexesha lokusebenza.

MHP = [ 0.045 / ( 100 - 30 )] ×ばつ 100 = 0.06 ( HP )

Ukwamkela i-1/4HP drive motor lukhetho olufanelekileyo.

I-Spiral Conveyor

Imifanekiso ebonisa apha ngasentla ngumzekelo wenkqubo yokuhambisa ejikelezayo enamaleko amathathu.Iingubo zendlela yokuthwala kunye nendlela yokubuya zenziwe ngezinto ze-HDPE.Ububanzi bebhanti bubonke yi-500mm kwaye yamkele i-HS-300B-HD kunye ne-sprockets enamazinyo ayi-8.Ubude becandelo elithwele ngokuthe tye kwi-drive kunye ne-idler end yi-1 mitha ngokulandelanayo.I-radius yayo yangaphakathi yokujika yi-1.5M, kwaye izinto zokuthutha ziibhokisi zeposi kwi-50Kg/M2.Isantya sokusebenza somthumeli si-25M / min, sithambekele ekuphakameni kwe-4M kwaye sisebenze kwindawo eyomileyo.Ubalo olunxulumeneyo lulandelayo.

Ukubalwa kweyunithi yoxinzelelo lulonke - TWS

IFOMU :

TW = TB ×ばつ FA

TWS = 958.7 ×ばつ 1.6 = 1533.9 ( Kg / M )

IFOMU :

TB = [ 2 ×ばつ R0 ×ばつ M + ( L1 + L2 ) ] ( WP + 2 WB ) ×ばつ FBW + ( WP ×ばつ H )

I-TB = [ 2 ×ばつ 3.1416 ×ばつ 2 ×ばつ 3 + ( 1 + 1 )] ( 50 + 2 ×ばつ 5.9 ) ×ばつ 0.35 + ( 50 ×ばつ 2 )

I-TB = 958.7 ( Kg / M )

Ukubalwa kweyunithi yoxinzelelo oluvumelekileyo - TA

IFOMU :

TA = BS ×ばつ FS ×ばつ FT

TA = 2118 ×ばつ 1.0 ×ばつ 0.95 = 2012 ( Kg / M )

Ngenxa yexabiso i-TA inkulu kune-TW;ngoko ke, ukwamkela Series 300B-HD ibhanti lukhetho olukhuselekileyo nolufanelekileyo.

Nceda ubhekisele kwisithuba seSprocket se-HS-300 kwiSahluko se-Drive Sprockets;isithuba esikhulu se-sprocket simalunga ne-145mm.
I-Deflection ratio ye-drive shaft - i-DS

IFOMU :

SL = ( TWS + SW ) ×ばつ BW

SL = ( 1533.9 + 11.48 ) ×ばつ 0.5 = 772.7 ( Kg )

IFOMU :

DS = 5 ×ばつ 10-4 ×ばつ [ ( SL ×ばつ SB3 ) / ( E ×ばつ I )]

DS = 5 ×ばつ 10-4 ×ばつ [ ( 772.7 ×ばつ 6003 ) / ( 19700 ×ばつ 174817 )] = 0.024 ( mm)

Ukuba isiphumo sobalo sincinci kunexabiso elisemgangathweni elidweliswe kwiTheyibhile yokuPhambuka;ukwamkela iibheringi ezimbini zebhola kwanele kwinkqubo.
Ukubalwa kwe-shaft torque - TS

IFOMU :

TS = TWS ×ばつ BW ×ばつ R

TS = 1533.9 ×ばつ 0.5 ×ばつ 92.5 = 70942.8 (kg - mm)

Xa kuthelekiswa ne-Maximum Torque Factor kwiyunithi ye-Shaft Selection, siyazi ukuba ukusetyenziswa kwe-38mm ×ばつ 38mm square shaft kukhuselekile kwaye kukhethwe ngokufanelekileyo.

Ukubalwa kwamandla ehashe - HP

IFOMU :

HP = 2.2 ×ばつ 10-4 ×ばつ [ ( TS ×ばつ V ) / R ]

I-HP = 2.2 ×ばつ 10-4 ×ばつ [ ( 70942.8 ×ばつ 4 ) / 60 = 1.04 ( HP )

Ngokubanzi, amandla omatshini we-center drive conveyor anokulahlekelwa malunga ne-40% ngexesha lokusebenza.

MHP = [ 1.04 / ( 100 - 40 )] ×ばつ 100 = 1.73 ( HP )

Ukwamkela i-2HP drive motor lukhetho olufanelekileyo.