Using AutoCAD, complete the following task: Given: Three people are initially at rest at Point-O. At time t-0, all three people begin to move. Sally runs due north for 5 minutes to Point-A at a 5:07min/mile pace. Sue walks due south-east for 13 minutes to Point-B at 3 mph. Sarah skips S80°W for 20 minutes to Point-C at 1 m/s. Find: Using Autocad, create a polygon by connecting points AB & BC & CA. Determine the area of the closed polygon in acres. 8

Q: 3. As the audio frequency of Fig. 11-7 goes down, what components of Fig. 12-4 must be modified for...

Q: Draw the updated network. Calculate the new project completion date. Check if there are changes to...

Q: = A 5 m high smooth vertical wall retains a clay backfill with c = 13 kN/m2, ' -25°, and y = 17.0...

Q: A vane shear test was conducted in a saturated soft clay, using a 100 mm x 260 mm vane. When the...

Q: Need assistance with d.

Q: H.W: Evaluate the integral 1. 1 1 }} 0 y x2exy dxdy 2. 1 ܐy 2 dxdy

Q: Please answer the following show me how to solve in your paper dont type thank you

Q: 5.25 Water from a pipe is diverted into a weigh tank for exactly 1 min. The increased weight in the...

Q: I really need help on b

Q: G-1 The drawing shows the beam (B) and girder (G) layout for the third floor of a commercial...

Q: As shown in the figure below, a 1.5 m ×ばつ 1.5 m footing is carrying a 400 kN load. P Depth (m) 0.0 1.0...

Q: Resuelve el problema uno

Q: 4-7 Nitrogen (molecular weight 28) expands reversibly in perfectly thermally insulated cylinder from...

Q: Existing Filter Design Parameters at 22.5 MGD: A) # of Filters: 5 B) #Bays per Filter: 1 C) Bay...

Q: A study of the properties of metal plate-connected trusses used for roof support yielded the...

Q: By using the yield line theory, determine the ultimate resisting moment per linear meter (m) for an...

Q: 12.36 Figure P12.36 shows a 3 ×ばつ 5 pile group consisting of 15 concrete piles of 400 mm diameter and...

Q: It proposed to provide pile foundation for a heavy column; the pile group consisting of 4 piles,...

Q: Given a side slope of 2:1, a road width of 10 m and cross-sectional area of 36.4 sq m, for the...

Q: An engineer is designing a fountain, as shown, and will install a nozzle that can produce a vertical...

Q: Factor of Safety Activity The lap joint is connected by three 20-mm diameter rivets. Assuming that...

Q: m A square slab is simply supported along all sides and is to be isotropically reinforced. Determine...

Q: I am doing an assignment regarding building diagnosis. Provide answer, links and citations for...

Q: 6. If the initial DO concentration of a diluted (1/50) wastewater sample is 9.0 mg/L and the UO...

Q: 2,789.10 FEET = HOW MANY METERS (M)?

Q: Complete the profile leveling notes in Table 1. Show the arithmetic check and sample calculations of...

Q: For an reinforced concrete two-way slab shown in figure under the load (P). (the slab continuous...

Q: 3 BAT For an reinforced concrete two-way slab shown in figure under the load (P). (the slab...

Q: Part 1: True or False. Indicate whether the following statements are True (T) or False (F) by...

Q: For Problem 7.2, calculate the optimal cycle length (Webster’s formulation) and the corresponding...

Q: Homework: Determine the proportions of the separate aggregates that will give a gradation within the...

Q: 3BAT For an reinforced concrete two-way slab shown in figure under the load (P). (the slab...

Q: Calculate the BMs (bending moments) at all the joints of the beam shown in Fig.1 using the moment...

Q: On page 1, in the first body paragraph ("In the United States...to be smart."), edit the Kaya source...

Q: A simply supported rectangular RC beam is to carry a uniform factored dead load of 1.2 kip/ft and a...

Q: Design an intake tower with gates meet the following requirement: • Normal water surface elevation =...

Q: An urban county with an area of 1,000 mile2 has an estimated 18 million miles of vehicular traffic...

Q: The beam shown in the figure below has lateral support at the ends only. The concentrated loads are...

Q: 4. Calculate the magnitude and direction of the resultant pressure-force on the gate as shown in...

Q: Consider the cross-sections illustrated in the next slides. Implement a cross-sectional analysis...

Q: Given a portion of a pipe network below. Determine the true discharge in each pipe using the...

Q: Example 5 By using the yield line theory, determine the moment (m) for an isotropic reinforced...

Q: Consider the three cases shown below, in which a soil column is subjected to different water heads...

Q: A single-angle tension member of A36 steel must resist a dead load of 35 kips and a live load of 84...

Q: Q5: Find the force in each member of truss in figure below. 10 kN -2 m- 4 m 2 m 5 kN 4 m 45

Q: Send me the solution to the following question based on the source and I do not want the solution...

Q: Pick the rural location of a project site in Victoria, and its catchment area-not bigger than 25...

Q: 1,5 m 1,5 m A 1,6 KN F 0,8 m E 0,8 m

Q: 1- Present worth analysis An Environmental engineer is considering two materials for use in a...

Q: I got 5.97 mm please show your work clearly. thank you