Problem Statement: A solid shaft assembly with a fix support is shown in Figure 1 along with 3 additional viewpoints presented on the right. A force of 10 kN is applied at Point C. The diameter of the shafts is 100 mm. 1. Determine the state of stress at Point A due to the applied external force, see section A for reference. Point A is located 500mm from the fix support. 2. Determine the state of stress at Point B due to the applied external force, see section A for reference. Point B is located 500mm from the fix support. Show your complete solution. x 500mm B A Z A B Section A (View towards -Z axis) 10KN 30° Fix 1500mm 500mm A B 10KN Support 10KN 4 x FIGURE 1 A B Z y 10KN 45° 400mm 400mm 500mm

Q: help me with this Question for revision purposes and as well with citation The office building was...

Q: Find the maximum bending stress in ksi for this beam if it is made from a W16x50 steel shape. If the...

Q: hoph - AT 10x AT 10.076 ht 0.076 0 0-1846112 14884 xh T 1.632m h-4- (1-22) h = 1.022m 14. The...

Q: 6. A lake with no outlet is fed by a river with a constant flow of 1200 ft3/s. Water evaporates from...

Q: Note: Provide a clear, step-by-step simplified handwritten solution (with no extra explanations)...

Q: A lagoon with volume 1,300 m3 has been receiving a steady flow of a non-conservative waste (rate...

Q: Please solve the question by hand with a detailed explanation of the steps.

Q: How can construction project managers find a balance between speeding up schedules and the risks of...

Q: Given the properties of the wide flange: Property Value d = 530 mm bf = 210 mm tw =...

Q: 7.2 An intersection has a four-timing-stage signal with the movements allowed in each timing stage...

Q: A W14 x 82 with 20 ft length column is part of a braced frame. The load and moments computed from...

Q: Find forces in all members of the truss shown in Fig. Also find reactions at supports. 12 kN 20 kN...

Q: I need detailed help solving this exercise from homework of Engineering Mathematics II.I do not...

Q: I do not know how to approach this problem

Q: I need detailed help solving this exercise from homework of Engineering Mathematics II.I do not...

Q: What is the horizontal reaction at A for the frame shown 4? a. 2.42 k b....

Q: I need detailed help solving this exercise from homework of Engineering Mathematics II.I do not...

Q: 10. A short column is subjected to an eccentric loading. The axial load P = 1000 kips and the...

Q: A fully grouted reinforced masonry wall is to be constructed of 8-in. CMU. The wall height is...

Q: Design the reinforced masonry beam in the wall shown below. The wall is to be constructed of fully...

Q: Q3 Design a secondary clarifier for an activated sludge process with a recycle rate of 25 percent, a...

Q: What is the fixed end moment FEMAB for the beam shown with a settlement of 1.2 in. at support B?...

Q: Average sludge production reported by members of the National Association of Clean Water Agencies is...

Q: 6-21 Four ×ばつ 1/4 angles are used to form the member shown in the accompanying illustration. The...

Q: 3. A level loop was run starting at BM 20 and going clockwise around the loop shown below in Figure...

Q: Determin the internal angle given the following:

Q: Problem 3 15 A W150 x 37 rolled-steel beam is used below. Let P150 kN, L-10 m and E 200 GPa. Find...

Q: B2. For the truss below, determine all member forces. Hint: see the provided slide with the problem...

Q: What is the value of the influence line for the bending moment around B at B for the beam shown?...

Q: QUANTITY SURVEYING

Q: مارت حولة ملانول 60 Design Deceleration tank and screen for W.W.T.P of flow-144000 m2 day Design...

Q: Q1) Compute the ultimate bearing capacity using the Vesic method 0.6 m 0.8 m 580 kN 200 kN y=17.29...

Q: H.W: show that the equations 1. (x+y)dy+(x-y)dx = 0 2. x2dy+(y2-xy)dx = 0 are homogeneous and solve:

Q: Determine the required solids retention time (SRT) of a completely mixed activated sludge aeration...

Q: 1) 4,739,281 SQ.FT. = ______________________ ACRES? 2) S 90°00'00" W IS ALSO KNOW AS WHAT CARDINAL...

Q: أ. ما هي شروط حديد التسليح المستخدم في موقع العمل بشكل عام وكيف يجب ان يكون ؟ ب. كم حلقة تحتاج لاساس...

Q: Please provide a handwritten solution to the question

Q: Question 5. This figure shows a cross section of an aqueduct that carries water at 50 m3/s. The...

Q: 6. The easiest method to solve the beam shown in question number 14 is A. Force method B. Slope...

Q: For an reinforced concrete two-way slab shown in figure under the load (P). (the slab continuous...

Q: A3-inch diameter water pipe carries a flow rate of 6 gallons per minute. The pipe is 100 feet long...

Q: What is the approximate axial force in girder EF of the frame shown? Use the portal method....

Q: Please answer the question in the picture.

Q: Calculate the BMs (bending moments) at all the joints of the beam shown in Fig.1 using the slope...

Q: P10.7 WP For the simply supported steel beam [E = 200 GPa; I = 129 ×ばつ 106 mm2] shown in Figure P10.7,...

Q: G 6-114. The cantilever wide-flange steel beam is subjected to the concentrated force of P = 600 N...

Q: A traffic count taken between 7:00 a.m. and 2:00 p.m. on a rural highway found the following hourly...

Q: I need detailed help solving this exercise from homework of Engineering Mathematics II.I do not...

Q: The 4-story building has a floor dead load D = 80 psf, floor live load , L = 100 psf, roof dead load...

Q: Planning is underway for the construction of a new railway section between Stockholm and Uppsala as...