1. The beam is supported by a roller constraint at B, which allows vertical displacement but resists axial load and moment. If the bar is subjected to the loading shown and constant El (L = 12 ft, E = 3100 ksi, I = 1728 in (rectangular section 12"x12"), w = 1 klf). Caution: pay attention to unit conversion between ft and in) x W B a. Sketch the deflected shape. L b. Determine the equations of the slope and the elastic curve using the coordinate x. First, solve this problem parametrically, and then substitute the numerical values for L, E, I, w at the end. There will be a significant penalty for solutions that do not calculate the slope and deflection as parametric functions. c. Specify the slope (in radians) at point A (parametrically and numerically). d. Specify the vertical displacement at point B (parametrically and numerically).

Q: Can you show me how to obtain these answers thanks, will rate!

Q: Solve for forces on pin C and D

Q: What are the advantages and disadvanages of using a bar chart in construction scheduling?

Q: The moisture content of wood test was performed according to ASTM D4442 procedure and produced the...

Q: find SFD and BMD

Q: a) For the truss shown in Fig 2, determine the stiffness matrices of elements 2, 3 and 4 in the in...

Q: H.W: Solve the differential equation y' - (1+x)(1 + y2) = 0

Q: I need detailed help solving this exercise from homework of Engineering Mathematics II.I do not...

Q: A3-inch diameter water pipe carries a flow rate of 6 gallons per minute. The pipe is 100 feet long...

Q: Calculate the area of the following polygon using the abscissa and projection method, taking into...

Q: Please use relationship method as I do not understand that one.

Q: Calculate ALL nodal displacements and ALL the member forces in the truss. Please use the ID's noted...

Q: using the conjugate beam method to determine the slop and vertical deflection at B. Take E=200GPa, I...

Q: A pure bacterial culture is growing in a warm, oxygenated, and nutrient rich solution present in a...

Q: What is the reaction moment at A for the frame shown? a. 222.1 k-ft b. 107.8...

Q: 10.53 Water is pumped through a vertical 10-cm new steel pipe to an elevated tank on the roof of a...

Q: Please answer the question in the picture. solve for the ground level and also for the 2nd level...

Q: kevin.w.wickline@wv.gov

Q: I do not know how to approach this problem

Q: The difference in water surface levels in two tanks, which are connected by three pipes in series of...

Q: For the portal frame determine the reactions at a using the approximate method if all supports are...

Q: 4th Order Rurka-Kutta Method This assignment will expand your skills on using Excel to perform some...

Q: For the loading system acting on the beam shown in Fig.(1) Determine the reactions at the supports....

Q: If you could help me answer these questions in matlab that would be great, I provided an additional...

Q: The 4-story building shown below has a dead load D = 90 psf, floor live load, L = 110 psf. The roof...

Q: I need detailed help solving this exercise from homework of Engineering Mathematics II.I do not...

Q: Please explain step by step

Q: FIG. P5.66 40 kN B 4 m A 20 kN 10 kN/m C 8 m 8 m

Q: Please answer the question from the picture, show each step and explain please. Thank you so much

Q: 3. Find the reinforcements for the mid span and supports for an interior 8 in. thick slab (S-2) in...

Q: Determine the global stiffness matrix of the beam shown in Fig. 3. Assume supports at 1 and 3 are...

Q: A k 000 6 ft A kips Bl D ft C C kips 10 ft 12 ft E B k/ft D E ft t

Q: Aum A waste incinerator stack emits 27,027 kg/yr of cadmium and has an effective stack might of 100...

Q: Please answer the two questions in detail and as best as you can. Please ensure it is 100% done by...

Q: 2. a) Consider a cable used for aerial tramway (see figure a). The span is 400 m. The unstretched...

Q: Fluid mechanics question Draw a free body diagram and properly explain each st

Q: Please explain step by step and show formula

Q: 10000 Quizl:Design a grit chamber for a horizontal velocity 250 mm/s, minimum flow 5,000 m3/day,...

Q: A cantilever beam ABC is loaded as shown in Figure 1. A is a fixed support. Assume E= 200 GPa and I...

Q: For the design of a shallow foundation, given the following: Soil: ' = 20° c' = 52 kN/m2 Unit...

Q: The figures below shows the framing plan and section of a reinforced concrete floor system. Floor...

Q: instructions: make sure to follow the instructions and provide complete and detailed solution...

Q: 1. For the system shown below, calculate the power supplied to the pump if its efficiency is 82%....

Q: A6.2- Given a simply supported beam with the typical cross-section as shown in the figure below....

Q: Land Use Hydrologic Area (acres) Soil Group A 25 Forestland-orchards B 30 B 45 Forest Oak-Aspen C 60...

Q: Text Book Problem 7.82 (page 261) Consider the total head-loss in the system forthis flow is 18.56...

Q: What is the shear and normal stresses of Point J and Point K?

Q: ۰۹:۲۵ ZV9 HW2-C.pdf Dept: Civil Eng. Kerbala HW2 3rd Year (C) Ex 4-1: The field capacity and wilting...

Q: Please answer the question in the picture.

Q: Hello, I would like to ask if the answer provided in this link is correct based on the floor plan...