NAG Library Routine Document

G05TJF

1 Purpose

2 Specification

3 Description

4 References

5 Parameters

1:   MODE – INTEGERInput

On entry: a code for selecting the operation to be performed by the routine.

$\mathbf{MODE}=0$

Set up reference vector only.

$\mathbf{MODE}=1$

Generate variates using reference vector set up in a prior call to G05TJF.

$\mathbf{MODE}=2$

Set up reference vector and generate variates.

$\mathbf{MODE}=3$

Generate variates without using the reference vector.

Constraint: $\mathbf{MODE}=0$, $1$, $2$ or $3$.

2:   N – INTEGERInput

On entry: $n$, the number of pseudorandom numbers to be generated.

Constraint: $\mathbf{N}\ge 0$.

3:   LAMBDA – REAL (KIND=nag_wp)Input

On entry: $\lambda$, the mean of the Poisson distribution.

Constraint: $\mathbf{LAMBDA}\ge 0.0$.

4:   R(LR) – REAL (KIND=nag_wp) arrayCommunication Array

On entry: if $\mathbf{MODE}=1$, the reference vector from the previous call to G05TJF.

If $\mathbf{MODE}=3$, R is not referenced by G05TJF.

On exit: the reference vector.

5:   LR – INTEGERInput

On entry: the dimension of the array R as declared in the (sub)program from which G05TJF is called.

Suggested values:

• if $\mathbf{MODE}\ne 3$, $\mathbf{LR}=30+20\times \sqrt{\mathbf{LAMBDA}}+\mathbf{LAMBDA}$;
• otherwise $\mathbf{LR}=1$.

Constraints:

• if $\mathbf{MODE}=0$ or $2$,
  • if $\sqrt{\mathbf{LAMBDA}}>7.15$, $\mathbf{LR}>9+\mathrm{int}\left(8.5+14.3\times \sqrt{\mathbf{LAMBDA}}\right)$;
  • otherwise $\mathbf{LR}>9+\mathrm{int}\left(\mathbf{LAMBDA}+7.15\times \sqrt{\mathbf{LAMBDA}}+8.5\right)$;
• if $\mathbf{MODE}=1$, LR must remain unchanged from the previous call to G05TJF.

6:   STATE($*$) – INTEGER arrayCommunication Array

Note: the actual argument supplied must be the array STATE supplied to the initialization routines G05KFF or G05KGF.

On entry: contains information on the selected base generator and its current state.

On exit: contains updated information on the state of the generator.

7:   X(N) – INTEGER arrayOutput

On exit: the $n$ pseudorandom numbers from the specified Poisson distribution.

8:   IFAIL – INTEGERInput/Output

On entry: IFAIL must be set to $0$, $-1\text{ or }1$. If you are unfamiliar with this parameter you should refer to Section 3.3 in the Essential Introduction for details.

For environments where it might be inappropriate to halt program execution when an error is detected, the value $-1\text{ or }1$ is recommended. If the output of error messages is undesirable, then the value $1$ is recommended. Otherwise, if you are not familiar with this parameter, the recommended value is $0$. When the value $-\mathbf{1}\text{ or }\mathbf{1}$ is used it is essential to test the value of IFAIL on exit.

On exit: $\mathbf{IFAIL}=\mathbf{0}$ unless the routine detects an error or a warning has been flagged (see Section 6).

6 Error Indicators and Warnings

$\mathbf{IFAIL}=1$

On entry, $\mathbf{MODE}\ne 0$, $1$, $2$ or $3$.

$\mathbf{IFAIL}=2$

On entry, $\mathbf{N}<0$.

$\mathbf{IFAIL}=3$

On entry, $\mathbf{LAMBDA}<0.0$.

$\mathbf{MODE}=0$ or $2$ and LAMBDA is such that LR would have to be larger than the largest representable integer. Use $\mathbf{MODE}=3$ in this case.

$\mathbf{IFAIL}=4$

On entry, LAMBDA is not the same as when R was set up in a previous call to G05TJF with $\mathbf{MODE}=0$ or $2$.

On entry, the R vector was not initialized correctly, or has been corrupted.

$\mathbf{IFAIL}=5$

On entry, LR is too small when $\mathbf{MODE}=0$ or $2$.

$\mathbf{IFAIL}=6$

On entry, STATE vector was not initialized or has been corrupted.

7 Accuracy

8 Further Comments

9 Example

9.1 Program Text

Program Text (g05tjfe.f90)

9.2 Program Data

Program Data (g05tjfe.d)

9.3 Program Results

Program Results (g05tjfe.r)