[Logic] Error in Logic 6.0

2002年4月20日 11:15:16 -0500

> -----Original Message-----
> From: [email protected] [mailto:[email protected]]On
> Behalf Of [email protected]
> Sent: Saturday, April 20, 2002 10:13 AM
> To: [email protected]
> Subject: Re: [Logic] Error in Logic 6.0
>>> Steve,
> This is a problem with Fox pro & Microsoft> Dennis know of it
>> and I described this problem 3 months ago in LOGic 5.
>> Acording to Dennis Fox pro has a problem reading numbers above 65k.
> I had hope there would be some kind of fix in LOGic 6.
>> Dennis subjested I turn off the "Edit Mode" for the 1010# look up. You
> must
> go into "Values Awards" under setup and turn off the 'Edit list' flag for

I would rather have that flog turned on, even with the problems, but it will
not allow me to do that. The flag is off and if I turn it on it gives an
error that says
non edited data already exists in the list table for 1010#. I do not
understand. It says go to the list form and convert to a regular list. I do
not understand that. I see no convert option.
Any help here appreciated.
I know I am getting close. :-)
> the
> 1010# field. This helps and the only problem I have on occasion is when I
> get a number
> not in the table. I have to add it to the list by hand or wait for an
> updated 1010# list,
> usually out by the end of the first week of each month.
>> Another problem you may run into is if you enter the a contact who is
> portable with a
> number. Like WB2JRI/5 OR KH6/WB2JRI, You must enter in the contact under
> his regular
> call and edit his portable statics after.
>> 73
>> Tony WB2JRI
>>>> On 2002年4月20日 09:08:03 -0400 "Stephen J. Schrack"
> <[email protected]> writes:
> > I am experiencing a similar problem, but not quite the same. Mine
> > only
> > happens when the 1010 number is a high number. In other words, The
> > 1010
> > automatic lookup (or manual) works fine until the 1010 number
> > happens to
> > be one of the higher numbers (60,000 or higher). Then I get the
> > error
> > message described below. Sometimes I can recover from that though. I
> > suspect it is a corruption of the 1010 list and was going to wait
> > and
> > see if the next 1010.txt has the same issue. Perhaps the corruption
> > takes place during import? My platform is WinXP Professional 384MB
> > RAM
> > on a 1ghz workstation.
> >
> > Best 73 de N3MX...STEVE
> >
> > -----Original Message-----
> > From: [email protected]
> > [mailto:[email protected]]
> > On Behalf Of Roland Guidry
> > Sent: Saturday, April 20, 2002 8:39 AM
> > To: [email protected]
> > Subject: [Logic] Error in Logic 6.0
> >
> > I am have difficulty with this new program, Logic 6.0 Build 6.0.104.
> > When my
> > cursor passes over the userfield 1010#, I get an error as shown with
> > the
> > attached gif pic. When I chose "no" the program exits and when
> > restarted, I
> > have to perform a clean then restart.
> >
> > Sometime I get an error message that says "Invalid Subscript
> > Reference"
> > Cancel or Ignore. If I "Ignore" program continues to run, if I
> > cancel I
> > get
> > other errors reported.
> >
> > The file I downloaded for 1010#'s came from Win1010 using their
> > 1010.txt
> > file. I do not have this problem with Logic 5.
> >
> > Has anyone encountered this same problem. I email [email protected] on
> > 4/18,
> > no response to date.
> >
> > Roland, WA5CHX
> >
> >
> > _______________________________________________
> > LOGic mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/logic
> >
> >
> >
> > _______________________________________________
> > LOGic mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/logic
>>> 73
>> Tony WB2JRI
>>> ________________________________________________________________
> GET INTERNET ACCESS FROM JUNO!
> Juno offers FREE or PREMIUM Internet access for less!
> Join Juno today! For your FREE software, visit:
> http://dl.www.juno.com/get/web/.
> _______________________________________________
> LOGic mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/logic
>