USB I2C Interface (BETA) Project

Project Introduction

General

This kit is based upon an original design by Jan G0BBL and provides a multi-faceted replacement for the older "Rocky" serial interface kit. The kit includes:

• the 0.6 inch by 1.5 inch circuit board
• all components that go on the circuit board
• a three foot long USB cable with male connector on one end
• an 8-pin plug for the I2C interface to the PIC socket on the application board
• and a piece of heat shrink to cover the USB I2C board.

• It enables control of the Automatic Band Pass Filter board on the Lite + Xtall RX V9.0
• The control of the programmable Oscillator on the V6.3 RXTX (and the older, now retired Lite + Xtrall V8.3 RX) kits, over a USB cable, using the I2C protocol of two serial streams (the clocking stream, named "SCL", and the data stream, named "SDA"). With the proper software drivers, this kit removes the 16 frequency constraint of the RX V8.3 and RXTX V6.3 kits
• It accepts dash, dot, and common inputs from a keyer for input to Rocky's embedded keyer module
• It provides PTT switching signals from Rocky to the interfaced RXTX V6.3 rig,
• An additional application could be with existing v6.2 RXTX boards where only the PTT control function and the paddles input function are desired.

For more information on the firmware and its capabilities/configuration, refer to Bob G8VOI's Users Manual and Fred PE0FKO's configuration manual. You should access and download relevant portions of these guides to assist you with the setup in the final phase of this build.

Ordering Information

Prices and availability of the kit and its options are found at the Softrock Ordering Website.

This is an initial set of documentation of the build process for the USB I2C Interface kit.

The build is in three stages:

• Component installation ("build")
• External Connection installation
• and final operation/testing with a connected rig

The builder should read each page completely, taking care to compare the "bare board" photos with the completed stage photos, before undertaking actual construction.

Project Schematic

(Resistor testpoints (hairpin, top, or left-hand lead), as physically installed on the board, are marked in the schematic with red dots)

Project Bill of Materials

Project Expert's (terse) Build Notes

• Inventory Bill of Materials (BOM)
• Interface to RX or RXTX

Project Detailed Build Notes

For the non-expert builders among us, this site takes you through a stage-by-stage build of the kit. Each stage is self-contained and outlines the steps to build and test the stage. This ensures that you will have a much better chance of success once you reach the last step, since you will have successfully built and tested each preceding stage before moving on to the next stage.

Each stage is listed below, in build order, and you can link to it by clicking on its name below (or in the header and/or footer of each web page).

• Inventory the Bill of Materials (BOM)
• Build and Test the Build Stage Stage
• Build and Test the External Connections Stage
• Build and Test the Interface to Rig(s) Stage

Background Info

Tools

Winding Inductors

To learn how to wind coils and transformers, please read the

• tips from the experts and then
• view the excellent videos on KC0WOXs Website
• or take a read of Dinesh's VU2FD guidelines.
• You can review the common construction techniques for inductors for details on toroidal and binocular inductors.

Soldering

If you are not experienced at soldering (and even if you are somewhat experienced at soldering), refer to Tom N0SS's excellent tutorial on basic soldering techniques.

The video below describes techniques for soldering SOIC 14 (and 16 and 8) SMDs

View the above in full-screen mode on Youtube.

For the more adventurous, there is a process using solder paste and an electric oven called the reflow process, which can be used to install all the SMT chips to one side of the PC Board. This is documented by Guenael Jouchet in the following Youtube segment:

[埋込みオブジェクト:http://www.youtube.com/v/gu0v8lfLcKg&hl=en&fs=1&]

• Read the Primer on SMT Soldering at the Sparkfun site. It is a very good read and it speaks great truths. Then take the time to watch the video tutorial on soldering an SOIC SMD IC.
• Solder Stations. Don't skimp here. Soldering deficiencies account for 80 percent of the problems surfaced in troubleshooting. It is preferable to have an ESD-safe station, with a grounded tip. A couple of good stations that are relatively inexpensive are:
  • [画像:Velleman VTSS5U]
    Velleman VTSS5U 50W Solder Station (approx 20ドル at Frys)
  • Haakko 936 ESD Solder Station (under 100ドル)

ESD Protection

• Avoid carpets in cool, dry areas.
• Leave PC cards and memory modules in their anti-static packaging until ready to be installed.
• Dissipate static electricity before handling any system components (PC cards, memory modules) by touching a grounded metal object, such as the system unit unpainted metal chassis.
• If possible, use antistatic devices, such as wrist straps and antistatic mats (see Radio Shack's Set for 25ドル or the JameCo AntiStatic mat for 15ドル)).
• Always hold a PC card or memory module by its edges. Avoid touching the contacts and components on the memory module.
• Before removing chips from insulator, put on the wrist strap connected to the ESD mat. All work with CMOS chips should be done with the wrist strap on.
• As an added precaution before first touching a chip, you should touch a finger to a grounded metal surface.
• If using a DMM, its outside should be in contact with the ground of the ESD mat, and both leads shorted to this ground before use.
• See the review of ESD Precautions at this link.

Work Area

• You will need a well-lit work area and a minimum of 3X magnification (the author uses a cheap magnifying fluorescent light with a 3X lens. This is supplemented by a hand-held 10 X loupe - with light - for close-in inspection of solder joints and SMT installation.
• You should use a cookie sheet or baking pan (with four sides raised approximately a half an inch) for your actual work space. It is highly recommended for building on top of in order to catch stray parts, especially the tiny SMT chips which, once they are launched by an errant tweezer squeeze, are nigh on impossible to find if they are not caught on the cookie sheet.

Misc Tools

• It is most important to solidly clamp the PCB in a holder when soldering. A "third-hand" (e.g., Panavise or the Hendricks kits PCB Vise) can hold your board while soldering. In a pinch, you can get by with a simple third-hand, alligator clip vise. Jan G0BBL suggests "A very cheap way is to screw a Large Document Clip to a woodblock which will clamp the side of a PCB."
• Magnifying Head Strap
• Tweezers (bent tip is preferable).
• A toothpick and some beeswax - these can be used to pickup SMT devices and hold them steady while soldering.
• Diagonal side cutters.
• Small, rounded jaw needle-nose pliers.
• Set of jewelers' screwdrivers
• An Exacto knife.
• Fine-grit emery paper.

Project Completed Stage

Top of the Board

Bottom of the Board

Project Testing

Each stage will have a "Testing" Section, outlining one or more tests that, when successfully completed, provide you with the confidence and assurance that you are heading in the right direction towards a fully tested and built transceiver.

When you perform a test, you should always record the results of the test where indicated in the Testing section. This will make troubleshooting via the reflector much easier, since you will be communicating with the experts using a standard testing and measurement regime.

This kit can be built and reliably tested using nothing more than a common multimeter. Tests assume that the builder has a decent digital multimeter of sufficiently high input impedance as to minimize circuit loading issues. Measurements will be taken of current draws, test point voltages, and resistances.