|
1 | | -# |
2 | | -# Arduino ESP32 |
3 | | -# |
| 1 | +# Arduino Settings |
| 2 | +CONFIG_FREERTOS_HZ=1000 |
4 | 3 | CONFIG_AUTOSTART_ARDUINO=y |
5 | | -# end of Arduino ESP32 |
6 | 4 |
|
7 | | -# |
8 | | -# FREERTOS |
9 | | -# |
10 | | -CONFIG_FREERTOS_HZ=1000 |
11 | | -# end of FREERTOS |
12 | | -# end of Component config |
| 5 | +# Log Levels |
| 6 | +# Boot Messages - Log level |
| 7 | +CONFIG_BOOTLOADER_LOG_LEVEL_ERROR=y |
| 8 | +# Arduino Log Level |
| 9 | +CONFIG_ARDUHAL_LOG_DEFAULT_LEVEL_INFO=y |
| 10 | +# IDF Log Level |
| 11 | +CONFIG_LOG_DEFAULT_LEVEL_ERROR=y |
| 12 | + |
| 13 | +# Default to 921600 baud when flashing and monitoring device |
| 14 | +CONFIG_ESPTOOLPY_BAUD_921600B=y |
| 15 | +CONFIG_ESPTOOLPY_BAUD=921600 |
| 16 | +CONFIG_ESPTOOLPY_COMPRESSED=y |
| 17 | +CONFIG_ESPTOOLPY_MONITOR_BAUD_115200B=y |
| 18 | +CONFIG_ESPTOOLPY_MONITOR_BAUD=115200 |
| 19 | +CONFIG_ESPTOOLPY_FLASHSIZE_4MB=y |
| 20 | + |
| 21 | +#enable BT |
| 22 | +CONFIG_BT_ENABLED=y |
| 23 | +CONFIG_BT_NIMBLE_ENABLED=y |
| 24 | + |
| 25 | +#disable BT connection reattempt |
| 26 | +CONFIG_BT_NIMBLE_ENABLE_CONN_REATTEMPT=n |
| 27 | + |
| 28 | +#enable lwip ipv6 autoconfig |
| 29 | +CONFIG_LWIP_IPV6_AUTOCONFIG=y |
| 30 | + |
| 31 | +# Use a custom partition table |
| 32 | +CONFIG_PARTITION_TABLE_CUSTOM=y |
| 33 | +CONFIG_PARTITION_TABLE_FILENAME="partitions.csv" |
| 34 | +CONFIG_PARTITION_TABLE_OFFSET=0xC000 |
| 35 | + |
| 36 | +# Disable chip shell |
| 37 | +CONFIG_ENABLE_CHIP_SHELL=n |
| 38 | + |
| 39 | +# Enable OTA Requester |
| 40 | +CONFIG_ENABLE_OTA_REQUESTOR=n |
| 41 | + |
| 42 | +#enable lwIP route hooks |
| 43 | +CONFIG_LWIP_HOOK_IP6_ROUTE_DEFAULT=y |
| 44 | +CONFIG_LWIP_HOOK_ND6_GET_GW_DEFAULT=y |
| 45 | + |
| 46 | +# disable softap by default |
| 47 | +CONFIG_ESP_WIFI_SOFTAP_SUPPORT=n |
| 48 | +CONFIG_ENABLE_WIFI_STATION=y |
| 49 | +CONFIG_ENABLE_WIFI_AP=n |
| 50 | + |
| 51 | +# Disable DS Peripheral |
| 52 | +CONFIG_ESP_SECURE_CERT_DS_PERIPHERAL=n |
| 53 | + |
| 54 | +# Use compact attribute storage mode |
| 55 | +CONFIG_ESP_MATTER_NVS_USE_COMPACT_ATTR_STORAGE=y |
13 | 56 |
|
14 | 57 | # Enable HKDF in mbedtls |
15 | 58 | CONFIG_MBEDTLS_HKDF_C=y |
| 59 | + |
| 60 | +# Increase LwIP IPv6 address number to 6 (MAX_FABRIC + 1) |
| 61 | +# unique local addresses for fabrics(MAX_FABRIC), a link local address(1) |
| 62 | +CONFIG_LWIP_IPV6_NUM_ADDRESSES=6 |
0 commit comments