Unanswered Questions
1,319 questions with no upvoted or accepted answers
6
votes
1
answer
2k
views
Ultrasonic Flowmeter Using TDC-GP22 and Arduino Uno
I'm working on a project of Ultrasonic Flow Meter with TDC-GP22 using Arduino UNO. I used the library of leokoppel
In my code,the configurations of the registers are copied from the Application Note ...
5
votes
0
answers
383
views
SPI between Master arduino and Slave arduino
How can I send the string from Slave SPI to Master SPI?
I want to write code in Bare Metal.
The problem which I am facing is I can't make out what will be my blocking function in Master SPI code when ...
5
votes
0
answers
2k
views
Modbus TCP/IP using Arduino uno and ENC28J60 module
I have this project where I need a modbus tcp server that will host a series of sensor data for other modbus client devices to read. I use this Library by Andresoarmento
This is the code i am using ...
5
votes
0
answers
428
views
DHT22 reading weird values
I just hooked up a DHT22 I had laying around in a parts drawer to test something and it is giving out some crazy wrong values, I am running the adafruit library's unified example and this is the ...
4
votes
0
answers
349
views
Is Arduino WiFi101 library fully compatible with Arduino MKR1000 with WiFi HW?
Will all the classes in this library work with the MKR1000 with wifi hardware?
The guide mentions "wifi shield".
So, does the library work exactly the same with the Arduino MKR100 (with the onboard ...
4
votes
0
answers
749
views
Nordic nRf905 (433MHZ) with arduino receive garbage data
I am interface Arduino with nRf905 in receive mode use 433 MHZ.
I Have follow this link http://www.electrodragon.com/w/NRF905_Transceiver_433MHz-Wireless_Module.
And for transmitter, I am use RF-...
4
votes
0
answers
674
views
RFID Code (and setup) works on an UNO but not on the Yun
We're using two RDM6300 RFID readers for this, and the code works when plugged into an UNO, but not when connected to the Yun. We have one of the rfids plugged into the rx pin (0 on the digital side) ...
3
votes
1
answer
179
views
Arduino R3 Uno Clone - When barrel plug connected there is 5V on USB. Why?
I have been using Arudino Megas for some projects and never had this problem.
Simply enough - I am powering arduino with 12V in via barrel and take power out via VIN to 12V low very low current small ...
3
votes
0
answers
297
views
Sim800l doesn't respond to AT commands
My SIM800L doesn't respond to AT commands. The serial monitor is simply blank.
And the led blinks every 3 seconds which means it is connected to a network
I power it through an LM2596 buck down ...
3
votes
0
answers
643
views
PCA9685 - Hardware problem with diode?
I'm working on a project, where I need to run several high-torque servos. For that I bought come of these PCA9685 boards.
I hooked everything up with my arduino and connected an external 5V - max 3A ...
3
votes
0
answers
226
views
220v lightbulb gradual dimmer
I am trying to turn my incandescent bulb gradually,say its brightness should go from zero to 100% in 10 mins. In doing so I found the following code and it works well but it's not as gradual as I ...
3
votes
0
answers
117
views
My port is grayed out?
Hello I have a question on why my port is grayed out when I go to upload?
I’ve watched so many YouTube videos on what’s the problem and have been trying to do everything but just nothing seems to work!...
3
votes
0
answers
217
views
ESP8266 01 doesn't react after baud rate change
Hello guys I have my ESP8266 connected to my Arduino. Then I typed in AT in the serial monitor. It confirmed this command with OK. After that I typed in AT+UART=9600, 8, 1, 0, 0 which gave me the ...
3
votes
1
answer
1k
views
Communication between two Arduinos using ENC28J60?
How can I connect and send data between two Arduinos using ENC28J60 ethernet adapters on both of them? Is there any guide or example code for me to take a look from or any library I can use to achieve ...
3
votes
0
answers
836
views
SPI register read returns 0x00 or 0xff
I am trying to interface a Arduino Uno with an ASM330LHH using SPI. Whenever I try to read any register, I either get 0xff or 0x00 on the serial monitor
The code I am using:
#include <SPI.h>
#...