Help Needed as I am little bit lost. I've procured a Pro Micro Board from sparkfun. Great little board and it work like clock work when using the standard Arduino Programming IDE.

Well Copied the code thru to the Eclipse Project, Hit compile and all seems well. But Trying to write the code to the device the following happens.

avrdude: Version 6.3-20171130 Copyright (c) 2000-2005 Brian Dean, http://www.bdmicro.com/ Copyright (c) 2007-2014 Joerg Wunsch

 System wide configuration file is "C:/Users/vente/.arduinocdt/packages/arduino/tools/avrdude/6.3.0-arduino14/etc/avrdude.conf"
 Using Port : COM5
 Using Programmer : avr109
 Overriding Baud Rate : 57600
 AVR Part : ATmega32U4
 Chip Erase delay : 9000 us
 PAGEL : PD7
 BS2 : PA0
 RESET disposition : dedicated
 RETRY pulse : SCK
 serial program mode : yes
 parallel program mode : yes
 Timeout : 200
 StabDelay : 100
 CmdexeDelay : 25
 SyncLoops : 32
 ByteDelay : 0
 PollIndex : 3
 PollValue : 0x53
 Memory Detail :
 Block Poll Page Polled
 Memory Type Mode Delay Size Indx Paged Size Size #Pages MinW MaxW ReadBack
 ----------- ---- ----- ----- ---- ------ ------ ---- ------ ----- ----- ---------
 eeprom 65 20 4 0 no 1024 4 0 9000 9000 0x00 0x00
 flash 65 6 128 0 yes 32768 128 256 4500 4500 0x00 0x00
 lfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
 hfuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
 efuse 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
 lock 0 0 0 0 no 1 0 0 9000 9000 0x00 0x00
 calibration 0 0 0 0 no 1 0 0 0 0 0x00 0x00
 signature 0 0 0 0 no 3 0 0 0 0 0x00 0x00
 Programmer Type : butterfly
 Description : Atmel AppNote AVR109 Boot Loader

Connecting to programmer: .avrdude: butterfly_recv(): programmer is not responding

avrdude: butterfly_recv(): programmer is not responding avrdude: butterfly_recv(): programmer is not responding avrdude: butterfly_recv(): programmer is not responding avrdude: butterfly_recv(): programmer is not responding avrdude: butterfly_recv(): programmer is not responding Found programmer: Id = "F"; type = @ Software Version = �.u; Hardware Version = �. avrdude: butterfly_recv(): programmer is not responding avrdude: butterfly_recv(): programmer is not responding avrdude: error: buffered memory access not supported. Maybe it isn't a butterfly/AVR109 but a AVR910 device? avrdude: initialization failed, rc=-1 Double check connections and try again, or use -F to override this check.

avrdude: butterfly_recv(): programmer is not responding avrdude: error: programmer did not respond to command: leave prog mode avrdude: butterfly_recv(): programmer is not responding avrdude: error: programmer did not respond to command: exit bootloader

avrdude done. Thank you.

I've setup the Programming interface a as a Leonardo Board. AVR ISP.

For some reason It seems as if and it might be me that the usb does not reset? and go into programming mode.

Please Help