actually I'm using ethernet shield w5100 hanrun HR911105A 16/02 with arduino uno (original)

#include <SPI.h>
#include <Ethernet.h>
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network.
// gateway and subnet are optional:
byte mac[] = {
 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02
};
IPAddress ip(192, 168, 1, 177);
IPAddress myDns(192,168,1, 1);
IPAddress gateway(192, 168, 1, 1);
IPAddress subnet(255, 255, 255, 0);
// telnet defaults to port 23
EthernetServer server(23);
boolean gotAMessage = false;// whether or not you got a message from the client yet
void setup() {
 // Open serial communications and wait for port to open:
 Serial.begin(9600);
 // this check is only needed on the Leonardo:
 while (!Serial) {
 ; // wait for serial port to connect. Needed for native USB port only
 }
 // start the Ethernet connection:
 Serial.println("Trying to get an IP address using DHCP");
 if (Ethernet.begin(mac) == 0) {
 Serial.println("Failed to configure Ethernet using DHCP");
 // initialize the Ethernet device not using DHCP:
 Ethernet.begin(mac, ip, myDns, gateway, subnet);
 }
 // print your local IP address:
 Serial.print("My IP address: ");
 ip = Ethernet.localIP();
 for (byte thisByte = 0; thisByte < 4; thisByte++) {
 // print the value of each byte of the IP address:
 Serial.print(ip[thisByte], DEC);
 Serial.print(".");
 }
 Serial.println();
 // start listening for clients
 server.begin();
}
void loop() {
 // wait for a new client:
 EthernetClient client = server.available();
 // when the client sends the first byte, say hello:
 if (client) {
 if (!gotAMessage) {
 Serial.println("We have a new client");
 client.println("Hello, client!");
 gotAMessage = true;
 }
 // read the bytes incoming from the client:
 char thisChar = client.read();
 // echo the bytes back to the client:
 server.write(thisChar);
 // echo the bytes to the server as well:
 Serial.print(thisChar);
 Ethernet.maintain();
 }
}

that code prints on the serial monitor the following :

so what is the problem why it is not connecting I tried all the examples of the ethernet but no one works , i don't know may be the problem is that i don't have a sticker of make address on the shield and I'm using the mac address of the examples. or maybe I'm writing the Ip address wrong , here is the data from the network connection details

my router is zte , model : ZXHNH108N

Actually I'm using a W5100 Hanrun HR911105A 16/02 Ethernet shield with an Arduino Uno (original).

#include <SPI.h>
#include <Ethernet.h>
// Enter a MAC address and IP address for your controller below.
// The IP address will be dependent on your local network.
// gateway and subnet are optional:
byte mac[] = {
 0x00, 0xAA, 0xBB, 0xCC, 0xDE, 0x02
};
IPAddress ip(192, 168, 1, 177);
IPAddress myDns(192,168,1, 1);
IPAddress gateway(192, 168, 1, 1);
IPAddress subnet(255, 255, 255, 0);
// telnet defaults to port 23
EthernetServer server(23);
boolean gotAMessage = false;// whether or not you got a message from the client yet
void setup() {
 Serial.begin(9600);
 // this check is only needed on the Leonardo:
 while (!Serial) {
 ; // wait for serial port to connect. Needed for native USB port only
 }
 // start the Ethernet connection:
 Serial.println("Trying to get an IP address using DHCP");
 if (Ethernet.begin(mac) == 0) {
 Serial.println("Failed to configure Ethernet using DHCP");
 // initialize the Ethernet device not using DHCP:
 Ethernet.begin(mac, ip, myDns, gateway, subnet);
 }
 // print your local IP address:
 Serial.print("My IP address: ");
 ip = Ethernet.localIP();
 for (byte thisByte = 0; thisByte < 4; thisByte++) {
 // print the value of each byte of the IP address:
 Serial.print(ip[thisByte], DEC);
 Serial.print(".");
 }
 Serial.println();
 // start listening for clients
 server.begin();
}
void loop() {
 // wait for a new client:
 EthernetClient client = server.available();
 // when the client sends the first byte, say hello:
 if (client) {
 if (!gotAMessage) {
 Serial.println("We have a new client");
 client.println("Hello, client!");
 gotAMessage = true;
 }
 // read the bytes incoming from the client:
 char thisChar = client.read();
 // echo the bytes back to the client:
 server.write(thisChar);
 // echo the bytes to the server as well:
 Serial.print(thisChar);
 Ethernet.maintain();
 }
}

That code prints the following on the serial monitor:

So what is the problem? Why it is not connecting? I tried all the ethernet examples, but not one works. I don't know, maybe the problem is that I don't have a sticker of MAC address on the shield and I'm using the MAC address of the examples. Or maybe I'm writing the IP address wrong? Here is the data from the network connection details.

My router is a ZTE model ZXHNH108N.