URL: https://linuxfr.org/forums/linux-debutant/posts/debutant-je-suis-incapable-de-comprendre-comment-installer-un-dr Title: Debutant je suis incapable de comprendre comment installer un driver sous Mandriva LE2005 Authors: goodrice Date: 2005年06月26日T12:57:02+02:00 Tags: Score: 0 Bonjour à tous, J'ai installé hier une Mandrake LE2005 sans aucun problème. J'ai néanmoins des soucis sur quelques périphériques. Le plus ennuyeux est mon Dongle Wifi USB ATMEL qui est reconnu mais non fonctionnel ( je le vois dans le tableau de bord dans inconnu/autre). J'ai un CD constructeur avec les pilotes Linux mais je ne comprends pas comment arriver à les installer, voici ce qu'il raconte :======================================================================= ATMEL PCMCIA PCI USB linux driver ======================================================================= +---------------------+ |PART A. Instructions.| +---------------------+ 1. Configuration. -- Run "make config" and answer a few questions. This will create a .config file. 2. Build and installation -- a. If a .config file exists then you need to do the following steps: # make all # make install b. If a .config file does not exist, then you need to do the following steps: # make realclean # make config After the configuration queries : # make all # make install Remember to login as root or use "su" before installing the drivers. 3. RF Board Type? -- There are several Atmel chips for PCMCIA and USB which can be combined with a bunch of RF boards. If you don't know what is the exact type of the board: a. Just build and install everything. b. Plug you PCMCIA or USB board in and look in /var/log/messages for more info Then consult the following table. USB (the product IDs below are Atmel's ones only !): PID | Atmel chip | RF board | driver ----------+------------+----------+-------- 7605 | 503A | RFMD | usbvnetr.o 7606 | 505 | RFMD | usbvnet5.o ( The 505 is currently not supported due to missing firmware.) If no driver is loaded on plugging your USB adapter, check if the (vendor ID,product ID) pair is already contained in any of the *_DEVICES defines in src/includes/usb/config.h. If yes, build a driver for this RF board and try again. If no, try to find out which RF board your adapter contains (look inside, check the FCC pictures of the device, or try out all RF boards). Add your product / vendor ID pair in the appropriate *_DEVICES define in the config.h file. Build and install again. On success, please notify the developers at sourceforge to include the new IDs. PCMCIA : ID | DRIVER -------------+--------------- AT76C502AR | PCMCIA RFMD AT76C502AR_D | PCMCIA RFMD revision D AT76C502AR_E | PCMCIA RFMD revision E AT76C504 | PCMCIA RFMD 504 c. If you cannot find your device's ID in the above table's than try to get the required information from the Manufacturer.... 4. TOOLS -- In order to use the ncurses based command line (lvnet) and the X windows (xvnet) applications you must enable the Wireless LAN (non-hamradio) option inside the kernel (and of course if it was disabled to rebuild your kernel). For help regarding the two tools try the corresponding man pages. Alternatively: Get the wireless tools (iwconfig et al) and use them. 5. STARTUP Options Configuration. In order for you to configure the startup options of your card ( PCMCIA or USB ) you follow the steps below : PCMCIA : - Edit the ATMEL WIRELESS entry in /etc/pcmcia/wireless.opts by adding your preferences off channel, essid, encryption etc. USB : - Edit the /root/.vnetrc file by adding your preferences of channel, essid, encryption etc.If you edit the file in order for your settings to take effect you have to uncomment the post-install entry in /etc/modules.conf for the corresponding module. GOOD LUCK :-) 6. Support. -- For any questions use the sourceforge project's mailing list: atmelwlandriver-users@lists.sourceforge.net The homepage of the project is [http://atmelwlandriver.sourceforge.net/(...)](http://atmelwlandriver.sourceforge.net/) +--------------------+ |PART B. Known Issues| +--------------------+ USB drivers:(START) ------------ The URB's going to the device are using the Adapter->devreq->length field which on some platforms can cause serious problems. This will be fixed very soon. There is also a report for a deadlock in the initialization routine. We cannot reproduce it so far. There is a serious "conflict" with the usb-uhci driver and atmel's board which leads to one problem. The system hangs :( ..... This never happens with the uhci driver. USB drivers:(END) ----------------- +------------+ |PART C. TODO| +------------+ Add support for different product and vendor ID's.... AU SECOURS

AltStyle によって変換されたページ (->オリジナル) /