同じハードの LS-WSGL で確認できないか、
LS-WSGL に LS-SL の HDD をセットして起動してみる。
Orion1 CPU = Low Checking DATA BUS Checking ADDRESS BUS> Checking hardware info ... === Strap status : 0x00802030 === === H/W boardId : 0x33 === === boardId : 0x1a === === micon_support: off ===> OK. === BUFFALO LS-WSGL/R1 U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_WSGL/R1 LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Oct 22 2008 - 20:00:59) Marvell version: 1.12.1 - TINY Buffalo Version: 1.23-1.00 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 200Mhz , TClock = 166Mhz USB 0: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Using 88E1118 phy buffalo_change_power_status> Read 0x3a buffalo_IsStopAtUbootStatus> MagicKey=0x3a buffalo_change_power_status> Read 0x3a buffalo_change_power_status> Read 0x3a buffalo_change_power_status> Writing 0x5c Please Press HDD power button to continue ... buffalo_change_power_status> Read 0x5c buffalo_change_power_status> Writing 0x3a Marvell Serial ATA Adapter Integrated Sata device found Device 0: OK Model: WDC WD5000BEVT-00ZAT0 Firm: 01.01A01 Ser#: WD-WX50A79U4140 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Using device ide0, partition 1 Loading from block device ide device 0, partition 1: Name: hda1 Type: U-Boot File:/uImage.buffalo Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - ide 0:1 ** serch_boot_drv (185)>No kernel_file 0 Using device ide0, partition 1 Loading from block device ide device 0, partition 1: Name: hda1 Type: U-Boot File:/initrd.buffalo Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - ide 0:1 ** serch_boot_drv (240)>No init_file 0 Using device ide1, partition 1 ** Bad partition 1 ** serch_boot_drv (185)>No kernel_file 1 Using device ide1, partition 1 ** Bad partition 1 ** serch_boot_drv (240)>No init_file 1 Lost all init_rd/boot が読めていないようだ
Orion1 CPU = Low Checking DATA BUS Checking ADDRESS BUS> Checking hardware info ... === Strap status : 0x00802030 === === H/W boardId : 0x33 === === boardId : 0x1a === === micon_support: off ===> OK. === BUFFALO LS-WSGL/R1 U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_WSGL/R1 LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Oct 22 2008 - 20:00:59) Marvell version: 1.12.1 - TINY Buffalo Version: 1.23-1.00 DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 200Mhz , TClock = 166Mhz USB 0: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Using 88E1118 phy buffalo_change_power_status> Read 0x3a buffalo_IsStopAtUbootStatus> MagicKey=0x3a buffalo_change_power_status> Read 0x3a buffalo_change_power_status> Read 0x3a buffalo_change_power_status> Writing 0x5c Please Press HDD power button to continue ... buffalo_change_power_status> Read 0x5c buffalo_change_power_status> Writing 0x3a Marvell Serial ATA Adapter Integrated Sata device found Device 1: OK Model: WDC WD5000BEVT-00ZAT0 Firm: 01.01A01 Ser#: WD-WX50A79U4140 Type: Hard Disk Supports 48-bit addressing Capacity: 476940.0 MB = 465.7 GB (976773168 x 512) Using device ide0, partition 1 ** Bad partition 1 ** serch_boot_drv (185)>No kernel_file 0 Using device ide0, partition 1 ** Bad partition 1 ** serch_boot_drv (240)>No init_file 0 Using device ide1, partition 1 Loading from block device ide device 1, partition 1: Name: hdb1 Type: U-Boot File:/uImage.buffalo Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - ide 1:1 ** serch_boot_drv (185)>No kernel_file 1 Using device ide1, partition 1 Loading from block device ide device 1, partition 1: Name: hdb1 Type: U-Boot File:/initrd.buffalo Failed to mount ext2 filesystem... ** Bad ext2 partition or disk - ide 1:1 ** serch_boot_drv (240)>No init_file 1 Lost all init_rdこちらも駄目。
LS-WSGL の U-Boot は
U-Boot 1.1.1 (Oct 22 2008 - 20:00:59) Marvell version: 1.12.1 - TINYLS-SL の U-Boot は
U-Boot 1.1.1 (May 28 2009 - 11:06:21) Marvell version: 1.12.1 - TINYバージョンは同じ。コンフィギュレーションが違う????