PCMCIA /A with Remote 2 Slot
PCMCIA /A with Rear Opening Slots (Maybe
Japan only?)
Half-Assed W95 Support
95 Bezel Hack
More Refined 95 Bezel "Hack"
J1 and J2 are HPDB68 pin connectors, identical to those used on Fast/Wide drives. The cable is 68 pin .025 pitch.
My Reader has a slightly different chip layout, but the SMD capacitors,
the oscillator, controller, and the J1 / J2 connectors are in the same
place.
Curses. This makes my PCMCIA outline look poor. I'll fix it by removing
all of Tatsuo's outlines from my site...
NOTE: An OPTIONS BY IBM HARDWARE MAINTENANCE MANUAL SUPPLEMENT (S83G-9902,
83G9902) is available in support of this product.
These adapters come with the brackets
required to install them into the special bay in the new IBM systems (6875
and 6885) or a standard 3.5-inch drive bay. Installation in a 5.25-inch
drive bay requires the use of a standard 3.5-inch to 5.25-inch drive bay
conversion kit (70G8165).
Posted by Landon
Sheely
I purchased one of these a while
ago for a project I was working on and had it installed in my 8595.
It did, indeed, work great under DOS/Win and OS/2 Warp. Problem is
that the adaptor uses the "stinger" chipset which is the same as what IBM
used in the ThinkPad 720 series. This chipset is
unsupported in Win9x and, if memory serves, you
can only use the real mode drivers and not have any 32-bit support.
Tis a bummer.
Editor's Note:
NT 4.0 will not even SEE it.
More Refined
95 Bezel "Hack"
Tom Webster quit doing one arm pushups
long enough to type:
Installation on a Model 95 is quite simple. Use
a QIC Tape Drive bezel, IBM part number 34F2719 (ASM 34F2721), and add
four 0.156 inch high, 0.127 ID, 0.25 (or there abouts) OD spacers, or equivilent
stack of number 4 flat washers, between the 'drive' and the skid.
This centers the 'drive' vertically in the bezel opening
with ample clearence to insert/remove the PCMCIA cards. NO BEZEL HACKING
REQUIRED. (Ed. What fun is that?)
Operating System requirements
The drivers supplied
with this adapter support DOS 5.0 and higher, Windows 3.1 and OS/2 2.1
Product Description
The Two-Slot PCMCIA
MCA adapter is intended for use in desktop and tower personal computers
to provide an interface to PCMCIA cards in those machines. The adapter
supports the R2.1 PCMCIA specifications.
HW - Installation (Adapter and Bay Assembly)
1.
Mark the cables as J1 and J2
2.
Plug the cable marked J1 into J1 connector on the logic card
3.
Plug the cable marked J2 into J2 connector on the logic card
4.
Power-off the computer and unplug the power cord
5.
Remove the cover (Computer)
6.
Plug the logic card into a 16-bit slot
7.
Mount the bay card assembly into the external DASD bay
8.
Plug the cable marked J1 into J1 connector on the bay card
9.
Plug the cable marked J2 into J2 connector on the bay card
10.Verify
that cables will not interfere with re-installation of cover.
Re-route the cables if there will be interference.
11.Re-install
the cover (Computer)
12.Plug
power cords back in the outlets and power-on the computer
For All Systems
Having successfully
installed this option into the computer, you are now ready to plug PCMCIA
cards into it. This adapter allows the hot plugging and removal of PCMCIA
cards. Depending on the PCMCIA card that is used, you may be required to
install the drivers which were supplied with that card.
Installing the Adapter Device Driver
DOS Driver Installation
1.
Install DOS (Disable the PCMCIA drivers, if these have been included in
the version of DOS)
2.
Insert Option Disk in A:, type A:\UINSTALL and press ENTER
3.
Select INSTALL DOS PCMCIA DEVICE DRIVERS for IBM Machines
4.
Follow the installation instructions shown on the display
5.
Select Option 17: Any with INTEL PCIC
Restart the system
The Option Driver will install two logical drives (i.e. D and E) for PCMCIA
memory cards under DOS. Use the utility EZPLAY.EXE to obtain the PCMCIA
cards information (card information structure- CIS) by typing EZPLAY and
pressing enter. Some PCMCIA cards such as the PCMIA IR cards need to be
enabled by its software first in order to display CIS.
Windows 3.1 Driver Installation (includes DOS
installation)
1.
Start Windows (Enhanced Mode)
2.
Select FILE from the Program Manager Window
3.
Select RUN from the pull-down menu
4.
Insert Option Disk in A:, type A:\PCMINSTW and press ENTER
5.
Select Select any with INTEL PCIC
6.
Follow the installation instructions shown on the display
7.
Restart system The Option Driver will install two logical drives (i.e.
D and E) for PCMCIA memory cards under DOS and Windows. Click on the icon
PlayAtWill to obtain PCMCIA card information (card information structure-
CIS)
8.
The utility DICRMU01.SYS may cause some configuration to run slowly. If
slow operation occurs, please edit the CONFIG.SYS file by selecting the
file editor and insert REM at the beginning of the line DEVICE=C:\EZPLAY\DICRMU01.SYS
OS/2 2.1 Driver Installation
1.
Start OS/2
2.
Start Full Screen OS/2
3.
Insert Option Disk in A:, type A:\PCMINST2 and press ENTER
4.
Select Select any with INTEL PCIC
5.
Follow the installation instructions shown on the display
6.
Shutdown and Restart the system
7.
Click on PlayAtWill icon to obtain PCMCIA card information (card information
structure- CIS)
Personal Experience- To install the dual slot adapter under OS/2 v.3, go to OS/2 System, System Setup, Selective Install, click on the button to the left of PCMCIA Support, choose the IBM ThinkPad 720.
Preparing this Adapter for Use
Having successfully
installed this option into the computer, you are now ready to plug PCMCIA
cards into it. This adapter allows the HOT PLUGGING and REMOVAL of PCMCIA
cards Depending on the PCMCIA card that you choose to use, you may be required
to install the drivers which were supplied with that card.
PCMCIA card does not operate in a slot
1.
Make sure that the card is completely inserted in the slot. There will
be an audible beep when the card is properly inserted or removed.
2.
Make sure that the device drivers for the PCMCIA card have been installed
in this computer.
PCMCIA card does not operate in either port
1.
Confirm cables are plugged according to instructions.
2.
Confirm bay card is installed in 3.5 or 5.25 Inch bay
Error message Invalid Drive Letter appears.
This may occur
if the host computer has assigned drive letters above C: for devices such
as a CD ROM, additional hard disk or partitioned hard drives.
Insert the following statement in the CONFIG.SYS before any device driver statements: lastdrive = # where # equals the letter of the last drive in the system. You must include two letters for the adapter and letters for all of the previously configured drives.
DOS Configuration Example
DEVICE=C:\WINDOWS\HIMEM.SYS
FILES=30
BUFFERS=30
DOS=HIGH,umb
SHELL=C:\DOS\COMMAND.COM
/P /E:512
LASTDRIVE=M
STACKS=9,258
DEVICE=C:\DOS\SETVER.EXE
DEVICE=C:\DOS\SMARTDRV.SYS
DEVICE=C:\DOS\EMM386.EXE
NOEMS X=C800-C9FF
DEVICE=C:\EZPLAY\SSDOSAT.SYS
/O
DEVICE=C:\EZPLAY\IBMDOSCS.SYS
DEVICE=C:\EZPLAY\RMUDOSAT.SYS
/MA=C800-C9FF
DEVICE=C:\EZPLAY\AUTODRV.SYS
C:\EZPLAY\AUTODRV.INI
DEVICE=C:\EZPLAY\DISKDRV.SYS
DOS CONFIG.SYS
The installation program modifies the DOS CONFIG.SYS
file to include the appropriate DEVICE statements in the following order.
DEVICE=x The letter x
specifies the Socket Services already installed on the computer.
DEVICE=y The letter
x specifies the Socket Services already installed on the computer.
DEVICE=[drive:][path] PCMATADD.SYS
/baseslot=n /stbtime=n
where:
[drive:][path] The parameters [drive:][path]
specify the location of the device driver file.
/baseslot=n This option sets the base slot address, where n specifies whether the address begins at (0) or (1). The default is 1. Set this switch to 0 only if you have a problem addressing the slots. If a value other than 0 or 1 is specified, this switch is ignored and the default setting is restored.
/stbtime=n This option enables the standby mode, where n specifies the number of minutes that will elapse before the card goes to standby mode. The minimum value is 5 minutes, the maximum is 20 minutes. If a value greater than 20 is specified, this switch is ignored. All sockets are effected when you set this switch. (This feature does not support solid state cards.)
OS/2 CONFIG.SYS file sequence
The installation program places the appropriate device statements in
the OS/2 CONFIG.SYS file. They MUST appear in the following order.
BASEDEV=OS2DASD.DMD
DEVICE=C:\OS2\xxxxxx.SYS
(the Card Services statement)
DEVICE=C:\OS2\PCMATAE.SYS
DEVICE=C:\OS2\xxxxxxxx.SYS (the Socket
Services statement)
BASEDEV=PCM2ATA.ADD
BASEDEV=OS2PCARD.DMD (Note... Card and Socket Services
are not supplied with this option)
switch options for the main device driver
BASEDEV=PCM2ATA.ADD [/s:n] [/i:m] [/stbtime:n] [/b] where:
/s:n This option recognizes the PCMCIA sockets, where n specifies the number of physical PCMCIA sockets available. The default is 2 sockets, the maximum is 4 sockets.
/i:m This option
ignores specific PCMCIA sockets, where m specifies the logical socket number
to be ignored. Multiple settings are allowed. This feature is useful when
a Type III card physically occupies two sockets.
Examples:
BASEDEV=PCM2ATA.ADD /i:1 (First socket is ignored)
BASEDEV=PCM2ATA.ADD /s:4 /i:2 /i:3 (Second and third sockets are
ignored)
/stbtime:n This option enables the standby mode. (Same as described above for DOS stbtime option)
/b This option specifies the OS/2 operating system to start (boot) from the PCMCIA-ATA card. If you specify this option, then PCMCIA.ADD module decreases the number of sockets specified by the /s switch because the startup PCMCIA-ATA card is treated as an internal IDE hard disk, not a PCMCIA-ATA card. When the OS/2 operating system starts (boots) from the PCMCIA-ATA card, if you use the /s:4 option w/o the /b option, the disk assigned to the last drive-letter will not be assigned to any physical socket. (To make this PC Card a bootable PC Card, see the documentation that came with the OS/2 operating system.)
Notes About the /b Option
1. Do not ignore the computer startup socket by the /i
option when you use the /b option. Because the PCM2ATA.ADD module
cannot examine whether or not the socket can start the operating
system, the PCM2ATA.ADD module decreases the number of supported sockets
by the /b option and subtracts the number of sockets to be ignored.
For example, when you add the /s:4 /b /i:2 options to the PCM2ATA.ADD
module, and the OS/2 operating system is started from socket 2, the
PCM2ATA.ADD module can manage only two sockets. Sockets 1 and 3 are assigned
and socket 4 is ignored.
2. This switch option applies only to the CONFIG.SYS file
residing on the PC Card. Do not specify this option on the CONFIG.SYS
file that resides on the internal hard disk drive.
3. If you started (booted) from the PC Card, do not remove
the card until you shut down the operating system.
Software Drivers:
There are several layers of software drivers that
allow the PCMCIA card and slot to function with the computer. These software
drivers allow the applications and user to make use of the PCMCIA hardware.
Which drivers are needed depends on the card, and the drivers used.
Card Services Card Services works
with the operating system to allocates memory, interrupts and other system
resources to the card and drivers.
PCMCS.EXE Phoenix DOS Card Services
IBMDOSCS.SYS Yamato (IBM) DOS Card Services
PCMCIA.SYS OS/2 2.1 Card Services
Socket Services
Socket Services provides a low level interface for
the socket hardware. Socket Services accepts configuration information
from Card Services, and reads low level card configuration data from the
PCMCIA card.
PCMSS Phoenix Socket Services
IBMDSS01.SYS Yamato (IBM) AT bus DOS Socket
Services
IBMDSS02.SYS Yamato (IBM) MCA Socket Services
IBM2SS01.SYS Yamato (IBM) AT bus OS/2 Socket
Services
Client and Super Client Enablers
Client Enablers can configure one specific card for use as a
standard peripheral device. A Client Enabler is specific to the card it
is written for, and works the same as a driver for that device. Super Client
Enablers have the ability to recognize and configure a wider range of cards
(two or more).
ESTDFM.EXE IBM Modem Client Enabler
MEGAHZ.EXE Megahertz modem Client Enabler
PCMSCD.EXE Phoenix Super Client Driver
AUTODRV.SYS Yamato Super Client Driver
Point Enablers
Point Enablers bypass Socket and (or) Card
services and function as a Client Enabler. Point Enablers can save memory
if one is available for the card, and matches the socket controller. Point
Enablers will usually not work with each other, or other PCMCIA drivers.
(There are no universal Point Enablers! Each is designed for a specific
card, and must be provided by the manufacturer.)
Other Drivers
Some sets
of PCMCIA drivers have additional drivers or utilities that take care of
one part or another of the complete job. Some PCMCIA drivers, like the
IBM-Yamato drivers, require POWER.EXE to be loaded before any of the PCMCIA
drivers. The IBM drivers also have a Resource Map Utility that lets you
tell the drivers which part of the excluded memory to use;
DICRMU01.SYS ISA Resource Map Utility (IBM)
DICRMU02.SYS MCA Resource Map Utility (IBM)
"Universal" PCMCIA Drivers
ThinkPad 350, 360, 510, 720, 750, 755, and PS/Note 425
all have compatible hardware. These models can use the Yamato PCMCIA drivers
with EasyPlay. The file TPPCMCIA.EXE, will create an install disk for the
Yamato drivers and EasyPlay. The file can be downloaded from the Internet.
Card Memory Requirements
PCMCIA
Card Services requires 4K to load and function. Some PCMCIA cards will
not make any other requirements, but some do. Modems and most memory
cards do not need any more memory. The memory that is needed has to be
set aside in the CONFIG.SYS file. To exclude 4K for Card Services, the
EMM386 line may look like this:
DEVICE=C:\DOS\EMM386.EXE X=B000-BFFF
For a system with an IBM Ethernet PCMCIA
adapter, 16K needs to be set aside;
DEVICE=C:\DOS\EMM386.EXE X=D400-D7FF
The exclude range will need to be increased if a
PCMCIA card is installed that needs more memory reserved for it.
Here are some of the common memory requirements that would need to be added
to
Card Services 4K;
IBM Token Ring card 16K RAM + 8K ROM = 24K
IBM Ethernet = 16K
IBM 3270 card = 8K
Notes:
Ricoh RF5C266 -- 1 SlotController
Rev. A can't use C0000 orD0000, Rev.B, C(Current)no restriction
Ricoh RF5C366 -- 2 Slot Controller
Rev. A can't use C0000 orD0000, Rev.B,C(current) no restrictions
Ricoh RF5C366L-- Low Profile version of RF5C366 silicon same as RF5C366Rev.
C