DDT COMMAND LIST
 
	 n/ Open loc n, type contents in current mode
	 / Retype loc pointed to by last address
	 n<cr> Modify currently opened loc to be n, close loc
	 <cr> Reset modes, go to command level
	 n<lf> Modify, close, open next loc
	 <lf> Advance to next item and display
	 n^ Modify, close, open previous loc
	 ^ Reverse to previous item
	 n<tab> Modify, close, open loc pointed to by last typed value
	 <tab> Open loc pointed to by last typed value
	 @	 Synonym for <tab>
	 n] Open location n, type as instr
	 ] Set temporary mode to instr, retype location
	 n{ Open location n, type as a numeric
	 { Set temporary mode to numeric, retype location
	 n[ Open location n, type as symbolic
	 [ Set temporary mode to symbolic, retype location
	 n!	 Open location n, don't type
	 n= Type value as numeric
	 = Retype value as numeric
	 n\ Examine display block at n
	 \ Examine display block pointed to by last address
	 $A Addresses will be typed as absolute numbers
	 $R Addresses will be typed relative to symbols
	 $I Change current mode to instruction type out
	 $N Change current mode to numeric type out
	 $S Change current mode to symbolic type out
	 $T Change current mode to ASCII text output
	 $Z Change current mode/length to .ASCIZ
	 $H Change to halfword (byte) mode
	 $W Change to (short)word mode
	 $L Change to longword mode
	 $mI Change current input radix to m
	 $mO Change current output radix to m
	 $mR Change input and output radix
	 $mD Change current display block size
		 Note that the initial modes are $S and $W. These
		 can be temporarily changed by the above commands and
		 will return to the permanent setting by a carriage
		 return. The settings can be permanently changed by
		 using two altmodes in the mode setting command
		 (e.g. $$T sets permanent ASCII mode)
	 $mS Change maximum symbol offset
		 This mode is 'permanent' i.e. once set, it
		 stays at that value.
	
	 n$iM Set machine dependant mode i to n.
		 The actual argument syntax may vary from machine to
		 machine.
	 n$iB Set breakpoint i at address n (i from 0 to 7 or can
	 be omitted)
	 $iB Remove breakpoint i
	 $B Remove all breakpoints
	 $V List (view) all breakpoints
		 Note that breakpoints should only be set at the start
		 of extended instructions. Setting a breakpoint in the
		 middle of an instruction will cause undefined randomness.
	
*	 $P Proceed from breakpoint
*	 m$P Proceed from breakpoint m times (without halting)
*	 ^P Single step the processor
*	 n^P Single step n times (without halting)
*	 ^X 'Execute' step the processor - treats JSR as an atomic
*	 n^X Execute step n times (without halting)
*	 $G Start execution at address in JOBSA (start of program)
*	 n$G Start executing program at location n.
Commands marked with a '*' can be executed only in the hard-core
debugger with the normal code halted.
Numbers 'm' may be typed either before or after the '$'; numbers 'n'
or 'i' must be typed where shown.
Where a value is called for, if the value is typed before the
'$' (if any), the value may be typed as a string of tokens, which may
be either numbers or known symbols (i.e. findable in the DDT symbol
table) separated by operators; the available operators are +, - and *.
If the value is typed after the '$' only a single number may be used;
these are read in decimal unless preceeded by a 0.
</div><div class="naked_ctrl">
<form action="/index.cgi/contrast" method="get" name="gate">
<p><a href="http://altstyle.alfasado.net">AltStyle</a> によって変換されたページ <a href="http://web.mit.edu/afs/net/project/cgw/src/ddt.68/ddt.cmds">(-&gt;オリジナル)</a>
/ <label>アドレス: <input type="text" name="naked_post_url" value="http://web.mit.edu/afs/net/project/cgw/src/ddt.68/ddt.cmds" size="22" /></label> <label>モード: <select name="naked_post_mode">
<option value="default">デフォルト</option>
<option value="speech">音声ブラウザ</option>
<option value="ruby">ルビ付き</option>
<option value="contrast" selected="selected">配色反転</option>
<option value="larger-text">文字拡大</option>
<option value="mobile">モバイル</option>
</select>
<input type="submit" value="表示" />
</p>
</form>
</div>