Hi,
I am new to xen. I have been able to boot the dom0 but not any
domU or guest operating systems. Here is my story. I apologize
it is long but wanted to provide details. I appreciate any
assistance I that might be provided.
The machine is a single-CPU Pentium 4 with 1 GB of RAM and 3
hard drives installed. It is fairly vanilla hardware (detail
available if needed).
The base OS is/was Fedora Core 3. It is installed with / on
/dev/hda1 and linux swap on /dev/hda2. By default it boots
into runlevel 3 (no X).
I began by installing the Linux bridge-utils and then
ZopeInterface 3.0.1 and then Twisted 2.0.1 and TwistedWeb 0.5.
I had no problems.
Next I downloaded the binary tarball
xen-2.0.6-install-x86_32.tgz, unpacked it, and ran install.sh
with no problems.
I added the following lines to my grub.conf file:
title Xen 2.0 / XenLinux 2.6
 kernel /boot/xen-2.0.gz dom0_mem=131072
 module /boot/vmlinuz-2.6-xen0 root=/dev/hda1 ro console=tty0
 module /boot/initrd-2.6.12-1.1372_FC3-2.6-xen0
The ramdisk I made by first running "depmod 2.6.11.10-xen0"
and then 
mkinitrd /boot/initrd-2.6.12-1.1372_FC3-2.6-xen0 2.6-xen0
Next I moved the TLS libraries out of the way as instructed in the
manual.
I then rebooted and booted into the Xen kernel. It appears to
be fine:
[root@garlic ~]# uname -a
Linux garlic.phys.uwm.edu 2.6.11.10-xen0 #1 Sun May 22
11:38:50 BST 2005 i686 i686 i386 GNU/Linux
I do not see anything particularly disturbing during boot
(only that sunrpc cannot be started).
Next I rebooted and used a Fedora Core 4 CD to install FC4. I
installed it with / on /dev/hdc1. During the install I chose
not to install a new GRUB and instead later edited the
existing grub.conf in the FC3 partition on /dev/hda1. I am
able to boot into the FC4 partition directly with no problem.
I copied the directory /lib/modules/2.6.11.10-xenU from the
FC3 partition on /dev/hda1 to the /lib/modules directory on
the FC4 partition on /dev/hdc1.
I next created a configuration file to try and boot FC4 as a
Xen domain. Here are the contents of the file:
kernel = "/boot/vmlinuz-2.6.11-xenU"
ramdisk = "/boot/initrd-2.6-xenU.img"
memory = 512
name = "FedoraCore4-01"
disk = [ 'phy:hdc1,hda1,w', 'phy:hda2,hda3,w']
dhcp="dhcp"
root = "/dev/hda1 ro"
extra = "3"
I also edited /etc/fstab on the FC4 partition in /dev/hdc1 and
changed / to be mounted on hda1 (the virtual one I assume
provided by Xen) and swap to be mounted on hda3 (again the
virtual one).
With all this in place I then do
xend start
xm create -c /etc/xen/xmfc4
I see the output
Using config file "/etc/xen/xmfc4"
and then the hardware hangs immediately and completely...no response 
in dom0 from keyboard and the machine is no longer ping-able.
I also tried the example from the manual (ttylinux): I
downloaded ttylinux-xen.bz2, unzipped it, and created the
configuration file
kernel = "/boot/vmlinuz-2.6-xenU"
memory = 64
name = 'ttylinux'
nics = 1
ip = '1.2.3.4'
disk = ['file:/root/ttylinux-xen,sda1,w']
root = '/dev/sda1 ro'
When I try to run
xend start
xm create -c /etc/xen/ttylinux
I get the same result--hardware hangs immediately and
completely with no keyboard and no network (not ping-able).
I have watched /var/log/messages while doing this but there is
nothing interesting written.
Again thanks for reading and I would appreciate any help you
can offer.
Sincerely,
Scott Koranda
_______________________________________________
Xen-users mailing list
Xen-users@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-users