Hi James,
I have tested with current tip.
My flash drive worked properly.
I found no regression with my environment.
The main difference between us is flash drive.
In your environment, do other devices become
the same error? Or, some devices work?
My test environment is as follows.
PC: Core 2 Quad Q9450 with Q35+ICH9DO
Xen: xen-3.4-testing.hg (c/s 19749)
Dom0 OS: CentOS 5.3
Dom0 kernel: linux-2.6.18-xen.hg (c/s 931)
DomU OS: CentOS 5.3
Dom0 kernel: linux-2.6.18-xen.hg (c/s 931)
Tested Device: Buffalo RUF2-R2GS
 (VendorID:0411, ProductID:0098)
dmesg output on domU:
vusb vusb-0: Xen USB2.0 Virtual Host Controller driver (usbfront)
drivers/usb/core/inode.c: creating file 'devices'
drivers/usb/core/inode.c: creating file '001'
vusb vusb-0: new USB bus registered, assigned bus number 1
usb usb1: default language 0x0409
usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: Xen USB2.0 Virtual Host Controller driver (usbfront)
usb usb1: Manufacturer: Linux 2.6.18.8-cs931-domU xen_hcd
usb usb1: SerialNumber: vusb-0
usb usb1: uevent
usb usb1: configuration #1 chosen from 1 choice
usb usb1: adding 1-0:1.0 (config #1, interface 0)
usb 1-0:1.0: uevent
hub 1-0:1.0: usb_probe_interface
hub 1-0:1.0: usb_probe_interface - got id
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
hub 1-0:1.0: standalone hub
hub 1-0:1.0: no power switching (usb 1.0)
hub 1-0:1.0: individual port over-current protection
hub 1-0:1.0: Single TT
hub 1-0:1.0: TT requires at most 8 FS bit times (666 ns)
hub 1-0:1.0: power on to power good time: 20ms
hub 1-0:1.0: local power source is good
hub 1-0:1.0: trying to enable port power on non-switchable hub
drivers/usb/core/inode.c: creating file '001'
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0000
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
hub 1-0:1.0: port 1, status 0501, change 0001, 480 Mb/s
hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x501
usb 1-1: new high speed USB device using vusb and address 2
usb 1-1: default language 0x0409
usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB Flash Disk
usb 1-1: Manufacturer: BUFFALO
usb 1-1: SerialNumber: F215700809250007
usb 1-1: uevent
usb 1-1: configuration #1 chosen from 1 choice
usb 1-1: adding 1-1:1.0 (config #1, interface 0)
usb 1-1:1.0: uevent
drivers/usb/core/inode.c: creating file '002'
hub 1-0:1.0: state 7 ports 8 chg 0000 evt 0002
SCSI subsystem initialized
Initializing USB Mass Storage driver...
usb-storage 1-1:1.0: usb_probe_interface
usb-storage 1-1:1.0: usb_probe_interface - got id
scsi0 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
 Vendor: BUFFALO Model: USB Flash Disk Rev: 4000
 Type: Direct-Access ANSI SCSI revision: 00
usb-storage: device scan complete
scsi 0:0:0:0: Attached scsi generic sg0 type 0
SCSI device sda: 3973120 512-byte hdwr sectors (2034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 3973120 512-byte hdwr sectors (2034 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: assuming drive cache: write through
 sda: sda1
sd 0:0:0:0: Attached scsi removable disk sda
Regards,
Noboru
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel