Hi,
some more info which I collected during physically accessing the machine
while rebooting. I was suprised that while it was not able to do
anything it was not a 'static' kernel panic, but the following text was
scrolling continously thru the screen:
"""
ata3: port reset, p_is 1 is e pis 1 cmd c017 tf 50 ss 113 se 0
ata3: status=0x50 { DriveReady SeekComplete }
sda: Current: sense key: No sense
 Additional sense: No additional sense information
"""
This and the same with 'ata2' and 'sdb'.
Please let me know if it has anything to do with the below metioned
setup.
Thanks.
Frank
-------- Forwarded Message --------
> From: Sipos Ferenc <frank@xxxxxxx>
> To: Keir Fraser <keir@xxxxxxxxxxxxx>
> Cc: xen-devel@xxxxxxxxxxxxxxxxxxx, xen-users@xxxxxxxxxxxxxxxxxxx
> Subject: Re: [Xen-users] Re: [Xen-devel] bt878 based dvr card vs. pci
> pass-thru
> Date: 2006年12月18日 10:56:06 +0100
>
> Hi All.
>
> > This file should contain your device id, not slot address. Find out the
> > numeric device id from 'lspci -n'.
> It was clearly stated in the docs that I should have used the output of
> 'lspci -n' but somehow it supressed my attention. Sorry for wasting your
> time on that.
>
> On an other note, I've did what you and the manual suggested and here is
> the result:
>
> """
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')e.0: enabling permissive
> mode configuration space accesses!
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')e.0: permissive mode is
> potentially unsafe!
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')e.1: enabling permissive
> mode configuration space accesses!
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')e.1: permissive mode is
> potentially unsafe!
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')f.0: enabling permissive
> mode configuration space accesses!
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')f.0: permissive mode is
> potentially unsafe!
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')f.1: enabling permissive
> mode configuration space accesses!
> Dec 18 10:47:43 hive kernel: pciback .&checktime(0000,07,0,':')f.1: permissive mode is
> potentially unsafe!
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')c.0: assign to
> virtual slot 0
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')c.1: assign to
> virtual slot 0 func 1
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')d.0: assign to
> virtual slot 1
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')d.1: assign to
> virtual slot 1 func 1
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')e.0: assign to
> virtual slot 2
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')e.1: assign to
> virtual slot 2 func 1
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')f.0: assign to
> virtual slot 3
> Dec 18 10:47:43 hive kernel: pciback: vpci: .&checktime(0000,07,0,':')f.1: assign to
> virtual slot 3 func 1
> Dec 18 10:47:43 hive kernel: device vif2.0 entered promiscuous mode
> Dec 18 10:47:43 hive kernel: ADDRCONF(NETDEV_UP): vif2.0: link is not
> ready
> Dec 18 10:47:47 hive kernel: ADDRCONF(NETDEV_CHANGE): vif2.0: link
> becomes ready
> Dec 18 10:47:47 hive kernel: xenbr0: port 3(vif2.0) entering learning
> state
> Dec 18 10:47:47 hive kernel: xenbr0: topology change detected,
> propagating
> Dec 18 10:47:47 hive kernel: xenbr0: port 3(vif2.0) entering forwarding
> state
> Dec 18 10:47:55 hive kernel: PCI: Enabling device .&checktime(0000,07,0,':')c.0 (0000 ->
> 0002)
> Dec 18 10:47:55 hive kernel: ACPI: PCI Interrupt .&checktime(0000,07,0,':')c.0[A] -> GSI
> 16 (level, low) -> IRQ 16
> Dec 18 10:47:55 hive kernel: PCI: Enabling device .&checktime(0000,07,0,':')d.0 (0000 ->
> 0002)
> Dec 18 10:47:55 hive kernel: ACPI: PCI Interrupt .&checktime(0000,07,0,':')d.0[A] -> GSI
> 17 (level, low) -> IRQ 20
> Dec 18 10:47:57 hive kernel: [__report_bad_irq+36/128] __report_bad_irq
> +0x24/0x80
> Dec 18 10:47:57 hive kernel: [note_interrupt+162/256] note_interrupt
> +0xa2/0x100
> Dec 18 10:47:57 hive kernel: [__do_IRQ+233/256] __do_IRQ+0xe9/0x100
> Dec 18 10:47:57 hive kernel: [do_IRQ+55/112] do_IRQ+0x37/0x70
> Dec 18 10:47:57 hive kernel: [__do_IRQ+179/256] __do_IRQ+0xb3/0x100
> Dec 18 10:47:57 hive kernel: [evtchn_do_upcall+146/256]
> evtchn_do_upcall+0x92/0x100
> Dec 18 10:47:57 hive kernel: [hypervisor_callback+61/72]
> hypervisor_callback+0x3d/0x48
> Dec 18 10:47:57 hive kernel: [<cd8b5107>] uhci_irq+0x27/0x190
> [uhci_hcd]
> Dec 18 10:47:57 hive kernel: [<cd8e03a4>] usb_hcd_irq+0x24/0x60
> [usbcore]
> Dec 18 10:47:57 hive kernel: [handle_IRQ_event+89/160] handle_IRQ_event
> +0x59/0xa0
> Dec 18 10:47:57 hive kernel: [__do_IRQ+138/256] __do_IRQ+0x8a/0x100
> Dec 18 10:47:57 hive kernel: [do_IRQ+55/112] do_IRQ+0x37/0x70
> Dec 18 10:47:57 hive kernel: [evtchn_do_upcall+146/256]
> evtchn_do_upcall+0x92/0x100
> Dec 18 10:47:57 hive kernel: [hypervisor_callback+61/72]
> hypervisor_callback+0x3d/0x48
> Dec 18 10:47:57 hive kernel: [safe_halt+32/80] safe_halt+0x20/0x50
> Dec 18 10:47:57 hive kernel: [start_hz_timer+18/32] start_hz_timer
> +0x12/0x20
> Dec 18 10:47:57 hive kernel: [xen_idle+44/96] xen_idle+0x2c/0x60
> Dec 18 10:47:57 hive kernel: [cpu_idle+139/224] cpu_idle+0x8b/0xe0
> Dec 18 10:47:57 hive kernel: [start_kernel+427/496] start_kernel
> +0x1ab/0x1f0
> Dec 18 10:47:57 hive kernel: [unknown_bootoption+0/480]
> unknown_bootoption+0x0/0x1e0
> """
>
> I needed to force my machine to reboot physically. Any suggestions are
> very welcome.
>
> (Ubuntu 6.10 - dom0 & domU - and Xen-3.0.3 binary install with Kodicom
> 4400R-like bt878 based DVR card)
> Should you need more info on my setup, I'm happy to provide you with
> that.
>
> Frank
>
>
>
> _______________________________________________
> Xen-users mailing list
> Xen-users@xxxxxxxxxxxxxxxxxxx
> http://lists.xensource.com/xen-users 
>
_______________________________________________
Xen-devel mailing list
Xen-devel@xxxxxxxxxxxxxxxxxxx
http://lists.xensource.com/xen-devel