[Logic] Error in Logic 6.0

2002年4月20日 11:57:55 -0400

Roland,
 i AM TUNED ON 28.3450 KHZ TIME NOW IS 15:58z
GIVE ME A CALL 'WB2JRI' AND I WILL THY AM HELP WE MAY HAVE TO MOVE 1010#
CALL FREQ.
73
Tony WB2JRI
On 2002年4月20日 09:30:28 -0500 "Roland Guidry"
<[email protected]> writes:
> I went into my list table and deleted the 1010# list. I then imported 
> a
> older list from March 2002. Doing this,did not cure the problem. 
> Cleaning
> indexes and updating awards did not help. I did get an error when 
> trying to
> import the 1010.txt file.
> "prg12e.err [Read Only]" -
> #include 'pda.h'
> Error in line 3: File does not exist.
> When I ignore the error, it loads data.
>> Does anyone have any suggestions.
>> Roland
>>>>> ----- Original Message -----
> From: "Stephen J. Schrack" <[email protected]>
> To: <[email protected]>
> Sent: Saturday, April 20, 2002 8:08 AM
> Subject: RE: [Logic] Error in Logic 6.0
>>> > I am experiencing a similar problem, but not quite the same. Mine 
> only
> > happens when the 1010 number is a high number. In other words, The 
> 1010
> > automatic lookup (or manual) works fine until the 1010 number 
> happens to
> > be one of the higher numbers (60,000 or higher). Then I get the 
> error
> > message described below. Sometimes I can recover from that though. 
> I
> > suspect it is a corruption of the 1010 list and was going to wait 
> and
> > see if the next 1010.txt has the same issue. Perhaps the 
> corruption
> > takes place during import? My platform is WinXP Professional 384MB 
> RAM
> > on a 1ghz workstation.
> >
> > Best 73 de N3MX...STEVE
> >
> > -----Original Message-----
> > From: [email protected] 
> [mailto:[email protected]]
> > On Behalf Of Roland Guidry
> > Sent: Saturday, April 20, 2002 8:39 AM
> > To: [email protected]
> > Subject: [Logic] Error in Logic 6.0
> >
> > I am have difficulty with this new program, Logic 6.0 Build 
> 6.0.104.
> > When my
> > cursor passes over the userfield 1010#, I get an error as shown 
> with the
> > attached gif pic. When I chose "no" the program exits and when
> > restarted, I
> > have to perform a clean then restart.
> >
> > Sometime I get an error message that says "Invalid Subscript 
> Reference"
> > Cancel or Ignore. If I "Ignore" program continues to run, if I 
> cancel I
> > get
> > other errors reported.
> >
> > The file I downloaded for 1010#'s came from Win1010 using their 
> 1010.txt
> > file. I do not have this problem with Logic 5.
> >
> > Has anyone encountered this same problem. I email [email protected] 
> on
> > 4/18,
> > no response to date.
> >
> > Roland, WA5CHX
> >
> >
> > _______________________________________________
> > LOGic mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/logic
> >
> >
> >
> > _______________________________________________
> > LOGic mailing list
> > [email protected]
> > http://mailman.qth.net/mailman/listinfo/logic
> >
>>> _______________________________________________
> LOGic mailing list
> [email protected]
> http://mailman.qth.net/mailman/listinfo/logic

73
Tony WB2JRI
________________________________________________________________
GET INTERNET ACCESS FROM JUNO!
Juno offers FREE or PREMIUM Internet access for less!
Join Juno today! For your FREE software, visit:
http://dl.www.juno.com/get/web/.