[Dxbase] New Problem

Thu Sep 13 14:30:00 EDT 2012

Searching the web, I came up with numerous ..."fixes"... , some benign,
some disastrous.
The consensus though is that it was caused by a Microsoft Security Update
and we can only wait for the next Update to fix the Previous Update.
In the meantime, it's a minor PITA that does no damage, so I just need
to remember to open DXBase twice !!
73, Dick, W1KSZ
On Thu, Sep 13, 2012 at 10:46 AM, Richard Solomon <dickw1ksz at gmail.com> wrote:
> OK, so what can I do about it ??
>> 73, Dick, W1KSZ
>> On Thu, Sep 13, 2012 at 10:35 AM, Neal Campbell <nealk3nc at me.com> wrote:
>> I think the technical term is that windows is "hosed up"!
>>>> 73
>> Neal
>> On Sep 13, 2012, at 12:48 PM, Jack <lennoxj at bellsouth.net> wrote:
>>>>> Dick,
>>>>>> No, I do not think DXbase is corrupt. I actually think that you did way too
>>> many "new" things .... brand new home built pc, two software packages
>>> recently installed, probably a lot of new drivers to go with you new pc...
>>> any one of these things could be causing the problem.
>>>>>> But, a quick search on the web reveals this info and there is a ton of other
>>> information about this same error message as well.
>>>>>> http://forums.cnet.com/7723-6142_102-243141/exception-processing-message-c00
>>> 00013/
>>>>>> Good luck.
>>> Jack
>>>>>>>>> -----Original Message-----
>>> From: dxbase-bounces at mailman.qth.net [mailto:dxbase-bounces at mailman.qth.net]
>>> On Behalf Of Richard Solomon
>>> Sent: Thursday, September 13, 2012 12:09 PM
>>> To: dxbase at mailman.qth.net
>>> Subject: [Dxbase] New Problem
>>>>>> I am running Ver.1.05 and all was well until I moved computers around !!
>>>>>> I built a new Windows 7 Machine and replaced my everyday computer with it.
>>> I moved that Computer into the shack. Now, it already had DXBase 2007 on it
>>> and it was working.
>>>>>> After installing Ham Radio Deluxe and the SignaLink interface and some other
>>> stuff I noticed this problem.
>>>>>> When I tried to enter a Call I get the following error message:
>>>>>> Windows - No Disk
>>> Exception Processing Message C0000013 Parameters 75b6bf7c 4 (then the 75b
>>> message repeated twice.
>>>>>> If I clear that error message I get:
>>>>>> Windows - No Disk
>>> There is no disk in the drive. Please insert Disk into Drive.
>>>>>> If I clear that message, close DXBase and re-open it, all is well. BUT, if I
>>> change Databases the above errors repeat themselves.
>>>>>> Can my copy of the DXBase program be corrupt ??
>>>>>> Thanks for any help,
>>>>>> 73, Dick, W1KSZ
>>> ______________________________________________________________
>>> Dxbase mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/dxbase
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:Dxbase at mailman.qth.net
>>>>>> This list hosted by: http://www.qsl.net
>>> Please help support this email list: http://www.qsl.net/donate.html
>>>>>> ______________________________________________________________
>>> Dxbase mailing list
>>> Home: http://mailman.qth.net/mailman/listinfo/dxbase
>>> Help: http://mailman.qth.net/mmfaq.htm
>>> Post: mailto:Dxbase at mailman.qth.net
>>>>>> This list hosted by: http://www.qsl.net
>>> Please help support this email list: http://www.qsl.net/donate.html
>>