[Dxbase] DXBase & MicroHam

Sat Jan 13 08:24:09 EST 2007

That was it ! I needed to check the " Connect Radio 1 Serial interface box "
which is actually shown in the picture ! Dah Thanks for pointing me in the
right direction.
Mike
-----Original Message-----
From: Tony Cash [mailto:tonycash at adelphia.net] 
Sent: Friday, January 12, 2007 10:40 PM
To: 'Dr. Michael Hunter'
Subject: RE: [Dxbase] DXBase & MicroHam
Does the Baud rate in DXB match with the radio?
Do you have DTR, RST or CTS checked in the radio 1 setup?
I know I must check RST for it to work with my TS2K.
Do you have the "Connect Radio 1 Serial Interface" box checked?
This must be checked before the radio will work.
73 de Tony, KD4K 
-----Original Message-----
From: dxbase-bounces at mailman.qth.net [mailto:dxbase-bounces at mailman.qth.net]
On Behalf Of Dr. Michael Hunter
Sent: Friday, January 12, 2007 8:48 PM
To: dxbase at mailman.qth.net
Subject: RE: [Dxbase] DXBase & MicroHam
The DXB rig tab I assume is the Radio1 under user options ? And yes when I
click the QSY box, nothing happens. My CAT system light is on, and my freq
changes under the Microham Router.
-----Original Message-----
From: FireBrick [mailto:w9ol at billnjudy.com] 
Sent: Friday, January 12, 2007 6:54 PM
To: drmike at infohiwy.net
Subject: RE: [Dxbase] DXBase & MicroHam
forgive me for asking, you do have the rig 'enabled' in the DXB rig tab?
and when you click on a cluster spot in the 'qsy' box, nothing happens?
On 1/12/2007 6:47:44 PM, Dr. Michael Hunter (drmike at infohiwy.net) wrote:
> Port page shows the freq as noted on the Ft 1kd. Com ports agree which
> is
> 3. And the stop bits is 2. Guess
> I'll need to talk to someone at MicroHam.
>>>> -----Original Message-----
> From: FireBrick [mailto:w9ol at billnjudy.com]
> Sent: Friday, January 12, 2007 6:35 PM
> To: Dr. Michael Hunter
> Subject: Re: [Dxbase] DXBase & MicroHam
>> It should work Mike
> I use it here.
> Take a look at the mHK ports page
> at the top the rig and frequency/mode should be displayed.
>> If not then your not communicating properly.
> "What we have here....is a failure to communicate!"
>> (name the movie)
>> Whatever port is entered into the Control field should equal the port
> selected in the rig window of the DXB setup window.
> You didn't
> say what rig.....
> the common gotcha if your using a Yaesu is the 2 (two) stop bits issue.
>>>> ----- Original Message -----
> From: "Dr. Michael Hunter" <drmike at infohiwy.net>
> To: <dxbase at mailman.qth.net>
> Sent: Friday, January 12, 2007 6:10 PM
> Subject: [Dxbase] DXBase & MicroHam
>>> > Just hooked up the new Microham last week and worked fine in the RU
> RTTY

______________________________________________________________
Dxbase mailing list
Home: http://mailman.qth.net/mailman/listinfo/dxbase
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Dxbase at mailman.qth.net
-- 
No virus found in this incoming message.
Checked by AVG Free Edition.
Version: 7.5.432 / Virus Database: 268.16.9/623 - Release Date: 1/11/2007
3:33 PM
 
-- 
No virus found in this outgoing message.
Checked by AVG Free Edition.
Version: 7.5.432 / Virus Database: 268.16.9/623 - Release Date: 1/11/2007
3:33 PM