[Dxbase] can not connect Internet cluster

Sun Dec 4 07:08:00 EST 2005

Toshi
Instead of 192....etc
try the Local host ip
127.0.0.1:7300 localhost ypoxkjlg
which should be the first line in your host file
you can check that by using File>Modify Host file
That what I use to transfer cluster spots from ARUser which is connected to a Spyder 
Cluster.
----- Original Message ----- 
From: "Toshimi Horie" <je2uff at dxer.cc>
To: "FireBrick" <w9ol at billnjudy.com>; <Dxbase at mailman.qth.net>
Sent: Saturday, December 03, 2005 11:59 PM
Subject: Re: [Dxbase] can not connect Internet cluster
>> On Sat, 3 Dec 2005 21:21:05 -0600
> "FireBrick" <w9ol at billnjudy.com> wrote:
>> Thanks replay.
>> Of course I can be connected to outside cluster.
> only I can connect local network cluster. That IP address is
> 192.168.1.20.
>> I changed a host file first.
> I wrote 192.168.1.20:7300 # JE2UFF as last line in host file.
>> I chose Internet among a Tool command and chose the host who added it
> some time ago afterwards.However, there is a state until now that is
> the connect result without being strange.
>> Why may not you be connected to a host in a local network?
>> My network router address is 192.168.1.1 , it is default setting value.
>> There is not only DXBase2006 to be able to be connected in other
> software. Choosing host which I added by a change of a host file,
> Internet setting, will there be an anything setting method elsewhere?
>> best regards!
>>> Toshi
>> I'm not sure exactly what your doing.
>> But....
>> 192.168.1.20:7300 is usually an IP from a router.
>>>> If you wish to connect to a cluster than you should use that cluster's IP directly.
>> In Tools>Options>User Options click on Internet.
>> Then where it says IP Host, choose the cluster you wish to connect with.
>>>> If the cluster you want to use is not listed, than you must use File>Modify Host File 
>> and
>> enter it.
>>>> Hope this is what you were asking about.
>>>>>> ----- Original Message ----- 
>> From: "Toshimi Horie" <je2uff at dxer.cc>
>> To: <Dxbase at mailman.qth.net>
>> Sent: Saturday, December 03, 2005 7:47 PM
>> Subject: [Dxbase] can not connect Internet cluster
>>>>>> > Hi all.
>> >
>> > My name is toshi, can use DXBase2006. It is nice sw. But now I have
>> > one problem in this software setting.
>> >
>> > Now running DX-spider software in my local network. It can use DDNS.
>> > so outside my network, can use domain. but inside.normaly use private
>> > address. one exsample, I can use RXCLUS then set up node address was
>> > 192.168.1.20 and port was 7300. It can connect DX-Spider from RXCLUS.
>> >
>> > But DXBase 2006 was same setting, host file modificated (add local IP)
>> > wrote as follows 192.168.1.20:7300
>> > but can not connect local DX-Spider host, DXBase2006as show
>> > "could not connect this site"
>> >
>> > Why other software (DX-telnet, RXCLUS,windows-telnet,etc) can connect
>> > host, Why can not connect DXBase2006.
>> >
>> > Who's know this countermager. Please tell me aonther set up.
>> >
>> > -- 
>> > Toshimi Horie <je2uff at dxer.cc>
>> >
>> > ______________________________________________________________
>> > Dxbase mailing list
>> > Home: http://mailman.qth.net/mailman/listinfo/dxbase
>> > Help: http://mailman.qth.net/mmfaq.htm
>> > Post: mailto:Dxbase at mailman.qth.net
>> >
>>>> -- 
> Toshimi Horie <je2uff at dxer.cc>
>>