[Dxbase] Anyone using DXBase 2005 with the Ten-Tec Orion?

Thu May 13 08:41:53 EDT 2004

Running 05 on a AMD Barton 3200.
I see no difference between 04 and 05.
Remember, with every added feature.
With every added item to search,
and with every added column to display
performance is effected.
a marginal system will show the most dramatic effect
but even previously 'fast' computers will result in processing time slowdowns.
----- Original Message ----- 
From: "William H. Hein" <Bill at AA6TT.com>
To: <dxbase at mailman.qth.net>
Sent: Thursday, May 13, 2004 6:26 AM
Subject: RE: [Dxbase] Anyone using DXBase 2005 with the Ten-Tec Orion?
Thanks for the Orion-DXBase 2005 tip, Ron. After I checked the CTS box as
you suggested the connection started working. I searched the Help file for
"Orion" and "CTS" and didn't get any hits, so I'm posting the info here for
other Orion users.
I like the new DXB 2005 features, but the program seems a little sluggish
compared to DXB 2004. Anyone else notice this?
73,
Bill NT1Y
-----Original Message-----
From: dxbase-bounces at mailman.qth.net [mailto:dxbase-bounces at mailman.qth.net]
On Behalf Of Kamar
Sent: Thursday, May 13, 2004 5:36 AM
To: williamhein at starband.net; dxbase at mailman.qth.net
Subject: RE: [Dxbase] Anyone using DXBase 2005 with the Ten-Tec Orion?
Bill,
I am running the Orion with Dxbase 2005. Dxbase properly loads and log the
mode and frequency from the Orion.
In the radio setup under User Options make sure that you have done the
following: the baud rate set to 57600, parity is None, Word Length is 8
bits, and Stop bits set to 1. Also, make sure the CTS box has a check mark
in it, and that the DTR High box is unchecked.
As you stated the Load Band/Mode from HF Transceiver must have a check mark
in its box.
Ron
NU1U
-----Original Message-----
From: dxbase-bounces at mailman.qth.net [mailto:dxbase-bounces at mailman.qth.net]
On Behalf Of William H. Hein
Sent: Monday, May 10, 2004 5:16 PM
To: dxbase at mailman.qth.net
Subject: [Dxbase] Anyone using DXBase 2005 with the Ten-Tec Orion?
I have my Ten-Tec Orion connected to my computer via a serial port. DXBase
2005 will QSY the radio and set the mode when I click on the QSY column in
the Internet Cluster window.
However, when I'm tuning the bands and making QSOs DXbase does not "Load
Band/Mode From HF Transceiver" (as I selected in User Options), instead just
grabbing the frequency and mode from the previously logged QSO.
"Connect HF Radio 1 Serial Interface" is selected, BTW.
Anyone else using a Ten-Tec Orion with DXBase 2005? If so, are you
experiencing this problem?
73,
Bill NT1Y
_______________________________________________
Dxbase mailing list
Dxbase at mailman.qth.net
http://mailman.qth.net/mailman/listinfo/dxbase
_______________________________________________
Dxbase mailing list
Dxbase at mailman.qth.net
http://mailman.qth.net/mailman/listinfo/dxbase
_______________________________________________
Dxbase mailing list
Dxbase at mailman.qth.net
http://mailman.qth.net/mailman/listinfo/dxbase