[DXBase] CW port still not working
Marty Ray
[email protected]
2002年11月28日 00:52:00 -0000
Okay! Now it's working. the problem was that Windows XP blocked the drivers
from being installed. I copied them into my windows drivers directory and
viola!
Thanks to everyone for their helpfull suggestions.
Regards,
Marty N9SE
----- Original Message -----
From: "Jack" <[email protected]>
To: "Marty Ray" <[email protected]>; "Tony Cash" <[email protected]>;
<[email protected]>
Sent: Wednesday, November 27, 2002 9:03 PM
Subject: Re: [DXBase] CW port still not working
> Marty,
>> Assuming you are using a standard serial port and you do not have any IRQ
> conflicts, then the setup is straightforward.
>> 1. Set user options for CW making sure you select the activate button for
> internal CW.
> 2. Make sure you have the required registry entries as described in the
> help file. Pay attention to the address that was assigned by DXbase. On
> some systems your actual address for your serial port may be different and
> you would have to modify the registry entry we made to agree with your
> actual hardware.
> 3. If you are using XP, check our web for some additional info about the
> drivers for that.
> 4. Make sure you have constructed a circuit similar to the one pictured
in
> the help file. This is similar to the ones used with CT and Writelog.
>> I can't think of nothing else.
>> Regards,
> Courtney
>> ----- Original Message -----
> From: "Marty Ray" <[email protected]>
> To: "Tony Cash" <[email protected]>; <[email protected]>
> Sent: Wednesday, November 27, 2002 11:25 AM
> Subject: Re: [DXBase] CW port still not working
>>> > Thanks. Tony. I tried com1 and it does the same thing. Radio works,
> "default
> > DTR 'HIGH' " keys the radio, but no cw out.
> >
> > Anybody have any other suggestions?
> >
> > 73 de Marty
> > ----- Original Message -----
> > From: "Tony Cash" <[email protected]>
> > To: "Marty Ray" <[email protected]>; "Matt Finlayson" <[email protected]>;
> > <[email protected]>
> > Sent: Wednesday, November 27, 2002 6:56 AM
> > Subject: Re: [DXBase] CW port still not working
> >
> >
> > > Is this com4 that you are trying to use, something other than a
standard
> > > windows com port. I know I have a USB to SERIAL adapter that I use
> > > here and the com ports on it are com 3 thru com 6 and they will not
work
> > > with the CW keying of DXBase. If I use com 1 or 2 that are located on
> the
> > > mother board then it works fine. Have you tried using the same setup
but
> > > switching
> > > it to com 1 or 2?
> > >
> > > I think Jack needs to fix this in the next version and make DXBase use
> ANY
> > > serial port that Windows recognizes, most programs already do but some
> > > don't.
> > >
> > > 73 de Tony, KD4K
> > >
> > > My Weather Page
> > > http://home.adelphia.net/~tonycash/
> > > My Ham Radio Page
> > > http://home.adelphia.net/~tonycash/kd4k/radio.html
> > > Sawnee Mountain (WB4GQX 147.15 +.600) Repeater Page
> > > http://home.adelphia.net/~tonycash/sawnee/index.html
> > >
> > > ----- Original Message -----
> > > From: "Marty Ray" <[email protected]>
> > > To: "Matt Finlayson" <[email protected]>; <[email protected]>
> > > Sent: Wednesday, November 27, 2002 1:29 AM
> > > Subject: Re: [DXBase] CW port still not working
> > >
> > >
> > > > I know some of the guys are using third party drivers or something
to
> > use
> > > > the parallel port with Windows XP, but I have heard that it doesn't
> work
> > > > very well. I just want to get it running per the help file, if I
> can...
> > > >
> > > > Thanks for the tip, though.
> > > >
> > > > One other interesting fact is that someone pointed out that there is
> no
> > > > IRQ17. I went back and checked and sure enough it is IRQ17. I also
> > checked
> > > > the other port on the PCI card and it also says IRQ17, but there are
> NO
> > > > CONFLICTS listed! Everything on those ports works, too. I'm running
my
> > > radio
> > > > on com4 and my rotor on com5, just no cw coming from the
DTR...hmm....
> > :
> > > (
> > > >
> > > > 73 de Marty
> > > >
> > > > ----- Original Message -----
> > > > From: "Matt Finlayson" <[email protected]>
> > > > To: "Marty Ray" <[email protected]>; <[email protected]>
> > > > Sent: Wednesday, November 27, 2002 4:29 AM
> > > > Subject: Re: [DXBase] CW port still not working
> > > >
> > > >
> > > > > Hi Marty,
> > > > >
> > > > > I use a laptop to run DXBase and my rig. Since I only have one
> serial
> > > > port,
> > > > > I use that to run the rig. I use the parallel port for CW. I paid
> 25ドル
> > > for
> > > > a
> > > > > CW-interface cable that goes from the parallel port to the key
jack
> on
> > > my
> > > > > radio. Works fine.
> > > > >
> > > > > 73, Matt K9KRY
> > > > >
> > > > > ----- Original Message -----
> > > > > From: "Marty Ray" <[email protected]>
> > > > > To: <[email protected]>
> > > > > Sent: Monday, November 25, 2002 6:15 PM
> > > > > Subject: [DXBase] CW port still not working
> > > > >
> > > > >
> > > > > > I have been trying to get the cw port working for a couple of
> weeks.
> > I
> > > > am
> > > > > > running windows XP, so I am using DTR on my radio serial port.
> (The
> > > help
> > > > > > file states "DXbase allows you to use the same serial port for
CW
> > that
> > > > is
> > > > > > used for your TNC or HF radio provided it does not use the DTR
> > > leads.")
> > > > > When
> > > > > > I set "default DTR High" on the radio port settings, my radio
keys
> > up,
> > > > > which
> > > > > > is correct. However, whe I try to send CW, I get nothing.
> > > > > >
> > > > > > I have tried setting the com port address in the driver using
> > > 'regedit'
> > > > to
> > > > > > no avail. When I look at my com port address in my
> > > > system\hardware\device
> > > > > > manger\com4\resources, it shows "I/O range C400-C407" and
"IRQ17",
> > so
> > > I
> > > > > set
> > > > > > the com4 data in regedit as follows:
> > > > > > "SYSTEM\CurrentControlSet\Services\DriverX\Parameters\Dxb98
COM4\
> > Port
> > > > > Base
> > > > > > 0x0000c400 (50176)"
> > > > > >
> > > > > > PortCount says "0x00000007 (7)"
> > > > > >
> > > > > > (Default) says "(value ot set)"
> > > > > >
> > > > > > and IgnoreConflicts says "0x00000001 (1)"
> > > > > >
> > > > > > Does anybody have any suggestions. I operate primarily CW, so
this
> > > > > > limitation may be enough for me to look at another logging
> program.
> > > > > >
> > > > > > Thanks for any assistance!
> > > > > >
> > > > > > Regards,
> > > > > >
> > > > > > Marty Ray N9SE
> > > > > >
> > > > > >
> > > > > > _______________________________________________
> > > > > > DXBase Reflector - Please visit us on the web at www.dxbase.com
> > > > > > - - - - - - - - - - - - - - - - - - - - - - -
> > > > > > To UNSUBSCRIBE please visit:
> > > > > > http://mailman.qth.net/mailman/listinfo/dxbase
> > > > > >
> > > > >
> > > > >
> > > >
> > > > _______________________________________________
> > > > DXBase Reflector - Please visit us on the web at www.dxbase.com
> > > > - - - - - - - - - - - - - - - - - - - - - - -
> > > > To UNSUBSCRIBE please visit:
> > > > http://mailman.qth.net/mailman/listinfo/dxbase
> > > >
> > >
> > >
> > >
> >
> > _______________________________________________
> > DXBase Reflector - Please visit us on the web at www.dxbase.com
> > - - - - - - - - - - - - - - - - - - - - - - -
> > To UNSUBSCRIBE please visit:
> > http://mailman.qth.net/mailman/listinfo/dxbase
> >
>>>