[DXBase] dxbpsk

2002年12月29日 13:39:04 -0500

Only four ways I can think of that would unregister a .dll
1. You installed a different version of this .dll through some other
software installation.
2. You upgraded your OS somehow and the registration info for some .dlls
was lost during the upgrade process.
3. You performed an unregister command.
4. A virus.
Regards,
Jack
----- Original Message -----
From: "Phil ON4VP" <[email protected]>
To: <[email protected]>
Sent: Sunday, December 29, 2002 1:27 PM
Subject: Re: [DXBase] dxbpsk
> Jack,
>> After completing a succesfull regsvr32 the engine 'runs' again.
> thanks for the tip, worked, why woudl it have been de-registered, no clue
> here ?
>> Anyhow, this is solved, thanks a lot !
>> Phil
>> ----- Original Message -----
> From: "Jack" <[email protected]>
> To: "Phil ON4VP" <[email protected]>
> Sent: Sunday, December 29, 2002 6:03 PM
> Subject: Re: [DXBase] dxbpsk
>>> > Phil,
> >
> > Well, I really don't know. The error message suggests that the
interface
> to
> > the PSK .dll has changed. When we communicate with the PSK modules, we
> send
> > parameters back and forth between DXbase and the PSK .dll files. If you
> > have installed a different version of the those .dll files possibly by
> > installing WinPSK, maybe your files are different and this would explain
> the
> > error. If this is the case, you would have to reinstall DXbase so that
> the
> > correct files that we expect are present.
> >
> > It might be that the solution I gave you previously would still work for
> the
> > error you are receiving. If the .dll registration has been changed on
> your
> > system, re-registering by the method I gave you might correct this.
> >
> > The only other thing I can think of is that memory on your machine has
> > become corrupted and your system is reporting the error because the
> > parameters are getting distorted by memory corruption.
> >
> > Hope one of these ideas solves the issue. We have not had this error
> > reported to us before.
> >
> > Regards,
> > Jack
> >
> > ----- Original Message -----
> > From: "Phil ON4VP" <[email protected]>
> > To: <[email protected]>
> > Sent: Sunday, December 29, 2002 11:41 AM
> > Subject: Re: [DXBase] dxbpsk
> >
> >
> > > Tnx Jack,
> > >
> > > The program does run, but I get an error message "invalid number of
> > > parameters" and when I clixk this error window away, the program shows
> the
> > > PSK interface but without any spectrum ??? the window is empty ???
This
> > > happened yesterday and never had it before. I have to quit the PSK
> > program,
> > > I can't doe anything ??? (no rx or tx works, when clicking settings
> menu,
> > > same error appears)
> > >
> > > this seems very strange, it happened suddenly and I didn't change
> anything
> > > in the dxbase files ....
> > >
> > > Phil ON4VP
> > >
> > > ----- Original Message -----
> > > From: "Jack" <[email protected]>
> > > To: "Phil ON4VP" <[email protected]>
> > > Sent: Sunday, December 29, 2002 4:19 PM
> > > Subject: Re: [DXBase] dxbpsk
> > >
> > >
> > > > Phil,
> > > >
> > > > The only thing I can suggest, without re-installing anything would
be
> > the
> > > > following which I copied from the Error section of the help file.
> Maybe
> > > you
> > > > could try this.
> > > >
> > > > If you attempt to run the DxbPSK program and receive an error
message
> > > before
> > > > the program boots up that says DxbPSK attempted to perform an
illegal
> > > > operation, it probably means that the WinPSKX.DLL file did not get
> > > > registered properly during our installation. You can register the
> file
> > > > yourself by following these steps:
> > > >
> > > > Locate the file called regsvr32.exe that will be located in your
> > > > Windows/System folder on Win95/98/ME. On NT and Win2000 it is
located
> > in
> > > > your WinNT/System32 folder. Copy regsvr32.exe into your DXbase 2002
> > > folder.
> > > >
> > > > Open a command box ( sometimes called a DOS box ) and using the
> standard
> > > > MSDOS command for change directory, perform a CD to the full path of
> > your
> > > > DXbase 2002 folder. At the DOS prompt in your DXbase 2002 folder,
> type
> > > the
> > > > following command:
> > > >
> > > > Regsvr32 WinPSKX.dll ( note there is one space between the 2 and
> the
> > > > W ).
> > > >
> > > > You should see a message that indicates that the file was
successfully
> > > > registered.
> > > >
> > > > Now, you can try to run the DxbPSK program again. If you continue
to
> > have
> > > > the same problem, then there is some other problem.
> > > >
> > > > Copyright �1999 - 2002 Scientific Solutions, Inc.
> > > > ----- Original Message -----
> > > > From: "Phil ON4VP" <[email protected]>
> > > > To: <[email protected]>
> > > > Sent: Sunday, December 29, 2002 9:32 AM
> > > > Subject: [DXBase] dxbpsk
> > > >
> > > >
> > > > Jack,
> > > >
> > > > I started to have problems running DXBasePSK module, won't load
> anymore
> > > (see
> > > > former message).
> > > > I installed a fresh copy of DXbase on a second computer and on this
> > > computer
> > > > the PSK module works.
> > > >
> > > > Can I copy some files to the first computer to check if things would
> > turn
> > > > back to normal, and if yes, which files do I need to copy th what
> > > > directories.
> > > >
> > > > Thanks, Phil ON4VP
> > > >
> > > > (PS I will check on the CW module on the fresh installed XP on the
> > laptop
> > > to
> > > > see if all works there with none of additional drivers installed
from
> > 3th
> > > > party software ...)
> > > >
> > > >
> > > >
> > > > --- StripMime Report -- processed MIME parts ---
> > > > multipart/alternative
> > > > text/plain (text body -- kept)
> > > > text/html
> > > > The reason this message is shown is because the post was in HTML
> > > > or had an attachment. Attachments are not allowed.
> > > > Please post in Plain-Text only.---
> > > > _______________________________________________
> > > > DXBase Reflector - Please visit us on the web at www.dxbase.com
> > > > - - - - - - - - - - - - - - - - - - - - - - -
> > > > To UNSUBSCRIBE please visit:
> > > > http://mailman.qth.net/mailman/listinfo/dxbase
> > > >
> > > >
> > > >
> > > >
> > >
> > >
> > > _______________________________________________
> > > DXBase Reflector - Please visit us on the web at www.dxbase.com
> > > - - - - - - - - - - - - - - - - - - - - - - -
> > > To UNSUBSCRIBE please visit:
> > > http://mailman.qth.net/mailman/listinfo/dxbase
> > >
> >
> >
> >
>>> _______________________________________________
> DXBase Reflector - Please visit us on the web at www.dxbase.com
> - - - - - - - - - - - - - - - - - - - - - - -
> To UNSUBSCRIBE please visit:
> http://mailman.qth.net/mailman/listinfo/dxbase